Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    P2121/19    Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance

for Preparation Click here


DESCRIPTION

HINT:
  1. This is the repair procedure for the accelerator pedal position sensor.
  2. This electrical throttle system does not use a throttle cable.
  3. This accelerator pedal position sensor is a non-contact type.

The accelerator pedal position sensor is mounted on the accelerator pedal and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and a malfunction of the accelerator position sensor.
In the accelerator pedal position sensor, the voltage applied to pedal terminals VPA and VPA2 of the ECM changes between 0 V and 5 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for the engine control, and the VPA2 is a signal to indicate the information about the opening angle which is used for detecting malfunctions. The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the throttle motor based on these signals.

G036462E01


DTC No.
DTC Detection Condition
Trouble Area
P2121/19
Condition (a) continues for 0.5 seconds:
(a) Difference between VPA1 and VPA2 exceeds the threshold
(1 trip detection logic)
  1. Accelerator pedal position sensor circuit
  2. Accelerator pedal position sensor
  3. ECM

WIRING DIAGRAM


A110962E01


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.


When using intelligent tester:

1.READ VALUE OF ACCELERATOR PEDAL POSITION SENSOR


    FI07052E02
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / ECD / Data List / Accel Position 1 and Accel Position 2.

  1. Read the values.

    Standard voltage:
    Accelerator Pedal
    Accel Position 1
    Accel Position 2
    Released
    0.6 to 1.0 V
    1.4 to 1.8 V
    Depressed
    2.9 to 4.2 V
    3.7 to 5.0 V



OK
REPLACE ECM
NG


2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)


    A099833E01
  1. Disconnect the B1 sensor connector.

  1. Disconnect the B9 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B1-1 (VCP2) - B9-27 (VCP2)
    B1-2 (EP2) - B9-29 (EPA2)
    B1-3 (VPA2) - B9-23 (VPA2)
    B1-4 (VCP1) - B9-20 (VCPA)
    B1-5 (EP1) - B9-28 (EPA)
    B1-6 (VPA1) - B9-22 (VPA)
    Below 1 Ω
    B1-1 (VCP2) or B9-27 (VCP2) - Body ground
    B1-2 (EP2) or B9-29 (EPA2) - Body ground
    B1-3 (VPA2) or B9-23 (VPA2) - Body ground
    B1-4 (VCP1) or B9-26 (VCPA) - Body ground
    B1-5 (EP1) or B9-28 (EPA) - Body ground
    B1-6 (VPA1) or B9-22 (VPA) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ACCELERATOR PEDAL ROD ASSEMBLY 


When not using intelligent tester:

1.CHECK ECM TERMINAL VOLTAGE (VPA AND VPA2 TERMINALS)


    A066060E09
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Tester Condition
    Accelerator Pedal Condition
    Specified Condition
    B9-22 (VPA) - B9-28 (EPA)
    Released
    0.6 to 1.0 V
    B9-22 (VPA) - B9-28 (EPA)
    Depressed
    2.9 to 4.2 V
    B9-23 (VPA2) - B9-29 (EPA2)
    Released
    1.4 to 1.8 V
    B9-23 (VPA2) - B9-29 (EPA2)
    Depressed
    3.7 to 5.0 V



OK
REPLACE ECM
NG


2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)


    A099833E01
  1. Disconnect the B1 sensor connector.

  1. Disconnect the B9 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B1-1 (VCP2) - B9-27 (VCP2)
    B1-2 (EP2) - B9-29 (EPA2)
    B1-3 (VPA2) - B9-23 (VPA2)
    B1-4 (VCP1) - B9-20 (VCPA)
    B1-5 (EP1) - B9-28 (EPA)
    B1-6 (VPA1) - B9-22 (VPA)
    Below 1 Ω
    B1-1 (VCP2) or B9-27 (VCP2) - Body ground
    B1-2 (EP2) or B9-29 (EPA2) - Body ground
    B1-3 (VPA2) or B9-23 (VPA2) - Body ground
    B1-4 (VCP1) or B9-26 (VCPA) - Body ground
    B1-5 (EP1) or B9-28 (EPA) - Body ground
    B1-6 (VPA1) or B9-22 (VPA) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ACCELERATOR PEDAL ROD ASSEMBLY