Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    P0504/51    Brake Switch "A" / "B" Correlation

for Preparation Click here


DESCRIPTION

In this system, the signals of the stop light switch's duplex system (STP and ST1-) are used to judge whether the brake system is abnormal or not. When the signals of depressing and releasing the brake pedal are detected simultaneously, the ECM interprets this as a malfunction of the stop light switch.

HINT:
Normal condition is shown in the table below.

Signal
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF


DTC No.
DTC Detection Condition
Trouble Area
P0504/51
  1. Conditions (a), (b) and (c) continue for 0.5 seconds or more:
    1. Ignition switch is ON
    2. Brake pedal is released
    3. STP signal is OFF when ST1- signal is OFF
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. ECM

WIRING DIAGRAM


A110959E01


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.


When using intelligent tester:

1.CHECK STOP LIGHT CIRCUIT
  1. Check if the stop light turn ON and OFF when the brake pedal is depressed and released.

    OK:
    Stop light turn ON and OFF normally.



NG
REPAIR OR REPLACE STOP LIGHT SWITCH CIRCUIT
OK


2.READ VALUE OF STP SIGNAL


    A080995E01
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / ECD / Data List / Stop Light Switch.

  1. Check the result.

    OK:
    Brake Pedal
    Specified Condition
    Depressed
    STP signal ON
    Released
    STP signal OFF

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Brake Pedal
    Specified Condition
    B7-14 (ST1-) - D3-7 (E1)
    Depressed
    Below 1.5 V
    B7-14 (ST1-) - D3-7 (E1)
    Released
    7.5 to 14 V



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


3.CHECK STOP LIGHT SWITCH ASSEMBLY


    A072924E05
  1. Remove the stop light switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pin not pushed
    Below 1 Ω
    3 - 4
    Pin not pushed
    10 kΩ or higher
    1 - 2
    Pin pushed
    10 kΩ or higher
    3 - 4
    Pin pushed
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)


    A099860E01
  1. Disconnect the B2 stop light switch connector.

  1. Disconnect the B7 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B2-1 - B7-15 (STP)
    Below 1 Ω
    B2-4 - B7-14 (ST1-)
    Below 1 Ω
    B2-1 or B7-15 (STP) - Body ground
    10 kΩ or higher
    B2-4 or B7-14 (ST1-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM 


When not using intelligent tester:

1.CHECK STOP LIGHT CIRCUIT
  1. Check if the stop lights turn ON and OFF when the brake pedal is depressed and released.

    OK:
    Stop lights turn ON and OFF normally.



NG
REPAIR OR REPLACE STOP LIGHT SWITCH CIRCUIT
OK


2.CHECK ECM TERMINAL VOLTAGE (STP AND ST1- TERMINALS)


    A080995E02
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Brake Pedal Condition
    Specified Condition
    B7-15 (STP) - D3-7 (E1)
    Depressed
    7.5 to 14 V
    B7-15 (STP) - D3-7 (E1)
    Released
    Below 1.5 V
    B7-14 (ST1-) - D3-7 (E1)
    Depressed
    Below 1.5 V
    B7-14 (ST1-) - D3-7 (E1)
    Released
    7.5 to 14 V



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


3.INSPECT STOP LIGHT SWITCH ASSEMBLY


    A072924E05
  1. Remove the stop light switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pin not pushed
    Below 1 Ω
    3 - 4
    Pin not pushed
    10 kΩ or higher
    1 - 2
    Pin pushed
    10 kΩ or higher
    3 - 4
    Pin pushed
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)


    A099860E01
  1. Disconnect the B2 switch connector.

  1. Disconnect the B7 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B2-1 - B7-15 (STP)
    Below 1 Ω
    B2-4 - B7-14 (ST1-)
    Below 1 Ω
    B2-1 or B7-15 (STP) - Body ground
    10 kΩ or higher
    B2-4 or B7-14 (ST1-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM