Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    P0335/12    Crankshaft Position Sensor "A" Circuit

DTC    P0339/13    Crankshaft Position Sensor "A" Circuit Intermittent

for Preparation Click here


DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and a pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of an iron core and magnet. The sensor plate rotates and as each tooth passes through the pickup coil, a pulse signal is created. The pickup coil generates 34 signals for each engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine RPM. Using these calculations, the common rail system is controlled.

DTC No.
DTC Detection Condition
Trouble Area
P0335/12
  1. No crankshaft position sensor signal to ECM while cranking
    (1 trip detection logic)
  2. No crankshaft position sensor signal to ECM with engine speed 600 rpm or more
    (1 trip detection logic)
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Crankshaft position sensor plate No. 1
  4. ECM
P0339/13
  1. No crankshaft position sensor signal to ECM is input for 0.05 seconds or more, and conditions (a), (b) and (c) are met
    (1 trip detection logic):
    1. Engine is at 1,000 rpm or more
    2. STA signal is OFF
    3. 3 seconds or more have elapsed after STA signal is switched from ON to OFF
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Crankshaft position sensor plate No. 1
  4. ECM

WIRING DIAGRAM


A110955E01


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. If no trouble is found in the diagnostic troubleshooting procedure of DTC P0335, troubleshoot the engine mechanical system.
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.INSPECT CRANKSHAFT POSITION SENSOR


    A072395E01
  1. Disconnect the D17 sensor connector.

  1. Measure the resistance of the sensor.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Cold
    1,630 to 2,740 Ω
    1 - 2
    Hot
    2,065 to 3,225 Ω

    HINT:
    In the table above, the terms "cold" and "hot" refer to the temperature of the coils. "Cold" means approximately -10° to 50°C (14° to 122°F). "Hot" means approximately 50° to 100°C (122° to 212°F).



NG
REPLACE CRANKSHAFT POSITION SENSOR
OK


2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)


    A099852E01
  1. Disconnect the D17 sensor connector.

  1. Disconnect the D1 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D17-1 - D1-27 (NE+)
    Below 1 Ω
    D17-2 - D1-34 (NE-)
    Below 1 Ω
    D17-1 or D1-27 (NE+) - Body ground
    10 kΩ or higher
    D17-2 or D1-34 (NE-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3.CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)


    BR03795E12
  1. Check the sensor Installation.

    OK:
    Sensor is installed correctly.



NG
REPAIR OR REPLACE CRANKSHAFT POSITION SENSOR
OK


4.CHECK CRANKSHAFT POSITION SENSOR PLATE NO.1
  1. Check the teeth of the crankshaft position sensor plate No. 1.

    OK:
    Plate's teeth do not have any cracks or deformation.



NG
REPLACE CRANKSHAFT POSITION SENSOR PLATE NO.1
OK

REPLACE ECM