Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    P0340/12    Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)

for Preparation Click here


DESCRIPTION

Camshaft position sensor (G signal) consists of a magnet, iron core and pickup coil.
The G signal plate has one tooth on its outer circumference and is installed on the pump drive shaft pulley. When the pump drive shaft pulley rotates, the protrusion on the signal plate and the air gap on the pickup coil change, causing fluctuations in the magnetic field and generating an electromotive force in the pickup coil.
The NE signal plate has 34 teeth and is mounted on the crank angle sensor plate. The NE signal sensor generates 34 signals at every engine revolution. The ECM detects the standard crankshaft angle based on the G signal and the actual crankshaft angle and the engine speed by the NE signal.

DTC No.
DTC Detection Condition
Trouble Area
P0340/12
  1. No camshaft position sensor signal to ECM while cranking
    (1 trip detection logic)
  2. No camshaft position sensor signal to ECM at engine speed of 650 rpm or more
    (1 trip detection logic)
  1. Open or short in camshaft position sensor circuit
  2. Camshaft position sensor
  3. Pump drive shaft pulley
  4. ECM

WIRING DIAGRAM


A110955E01


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.INSPECT CAMSHAFT POSITION SENSOR


    A064984E01
  1. Disconnect the D10 sensor connector.

  1. Measure the resistance of the position sensor.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    835 to 1,400 Ω at cold
    1 - 2
    1,060 to 1,645 Ω at hot

    HINT:
    In the table above, the terms "cold" and "hot" refer to the temperature of the coils. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).



NG
REPLACE CAMSHAFT POSITION SENSOR
OK


2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)


    A099853E01
  1. Disconnect the D10 sensor connector.

  1. Disconnect the D3 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D10-1 - D3-23 (G+)
    Below 1 Ω
    D10-2 - D3-31 (G-)
    Below 1 Ω
    D10-1 or D3-23 (G+) - Body ground
    10 kΩ or higher
    D10-2 or D3-31 (G-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)


    BR03795E14
  1. Check the sensor installation.

    OK:
    Sensor is installed correctly.



NG
REPAIR OR REPLACE CAMSHAFT POSITION SENSOR
OK


4.CONFIRM SUPPLY PUMP DRIVE SHAFT PULLEY
  1. Check the teeth of the pump drive shaft pulley.

    OK:
    Pulley's teeth do not have any cracks or deformation.



NG
REPLACE SUPPLY PUMP DRIVE SHAFT PULLEY
OK

REPLACE ECM