Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    P0200/97    Injector Circuit / Open

for Preparation Click here


DESCRIPTION

The EDU has been adopted to drive the injectors at high speeds. The EDU delivers high-speed driving under highly-pressurized fuel conditions using the DC/DC converter, which provides a high-voltage and quick- charging system.
Soon after the EDU receives an injection command (IJT) signal from the ECM, the EDU responds to the command with an injector injection confirmation (IJF) signal when the current is applied to the injector.

A099226E01


DTC No.
DTC Detection Condition
Trouble Area
P0200/97
Open or short in EDU or injector circuit
After engine is started, there is no IJF signal from EDU to ECM, despite ECM sending IJT signal to EDU
(1 trip detection logic)
  1. Open or short in EDU circuit
  2. Injector
  3. EDU
  4. ECM

HINT:
DTC P0200/97 is detected when start the engine and let it idle for 30 seconds.


MONITOR DESCRIPTION

  1. P0200/97 (Open or short in EDU or injector circuit):
    The ECM continuously monitors both injection command (IJT) signals and injection confirmation (IJF) signal. This DTC will be set if the ECM judges that the number of IJT signals and IJF signals are inconsistent.
    The injectors are grounded over a Field Effect Transistor (FET) and a serial resistor. This resistor creates a voltage drop, which is monitored by the EDU (injector drive circuit), in relation to the current drawn by the injector. When the injector current becomes too high, the voltage drop over the resistor exceeds a specified level and no IJF signal for that cylinder is sent to the ECM.
    P0200/97 refers to a malfunction in the EDU or injector circuit.
    If this DTC is set, the ECM enters fail-safe mode and limits engine power. The fail-safe mode continues until the ignition switch is turned OFF.

G037535E01


MONITOR STRATEGY


Required sensors
IJF signal from EDU
Frequency of operation
Continuous
Duration
10 seconds
MIL operation
1 driving cycle

TYPICAL ENABLING CONDITIONS


Item
Specification
Specification

Minimum
Maximum
Engine speed
500 rpm
-
Battery voltage
11 V
-
Engine switch
ON
ON

TYPICAL MALFUNCTION THRESHOLDS


Threshold
The injection missing counter* for all the cylinders, or for one individual cylinder, reaches a specified number (taking approximately 1 second after starting the engine)
*: Increments when no IJF signal is received from the EDU despite the ECM sending IJT signals

WIRING DIAGRAM


A110953E01


A110954E01


INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the injector, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.INSPECT INJECTOR ASSEMBLY


    A081503E01
  1. Disconnect the D24, D25, D26 and D27 injector connectors.

  1. Measure the resistance of the injector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    0.85 to 1.05 Ω



NG
REPLACE INJECTOR ASSEMBLY
OK


2.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - EDU)


    A099847E01
  1. Check the wire harness between the injector and EDU (INJ terminal).

    1. Disconnect the D24, D25, D26 and D27 connectors.

    2. Disconnect the B13 EDU connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      D24-2 - B13-4 (INJ1)
      Below 1 Ω
      D25-2 - B13-2 (INJ2)
      Below 1 Ω
      D26-2 - B13-1 (INJ3)
      Below 1 Ω
      D27-2 - B13-3 (INJ4)
      Below 1 Ω
      D24-1 - B13-5 (COM1)
      Below 1 Ω
      D25-1 - B13-6 (COM2)
      Below 1 Ω
      D26-1 - B13-6 (COM2)
      Below 1 Ω
      D27-1 - B13-5 (COM1)
      Below 1 Ω
      D24-2 or B13-4 (INJ1) - Body ground
      10 kΩ or higher
      D25-2 or B13-2 (INJ2) - Body ground
      10 kΩ or higher
      D26-2 or B13-1 (INJ3) - Body ground
      10 kΩ or higher
      D27-2 or B13-3 (INJ4) - Body ground
      10 kΩ or higher
      D24-1 or B13-5 (COM1) - Body ground
      10 kΩ or higher
      D25-1 or B13-6 (COM2) - Body ground
      10 kΩ or higher
      D26-1 or B13-6 (COM2) - Body ground
      10 kΩ or higher
      D27-1 or B13-5 (COM1) - Body ground
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (EDU - ECM)


    A099849E01
  1. Disconnect the B15 EDU connector.

  1. Disconnect the D1 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B15-6 (#1) - D1-24 (#1)
    Below 1 Ω
    B15-3 (#2) - D1-23 (#2)
    Below 1 Ω
    B15-2 (#3) - D1-22 (#3)
    Below 1 Ω
    B15-5 (#4) - D1-21 (#4)
    Below 1 Ω
    B15-7 (INJF) - D1-25 (INJF)
    Below 1 Ω
    B15-6 (#1) or D1-24 (#1) - Body ground
    10 kΩ or higher
    B15-3 (#2) or D1-23 (#2) - Body ground
    10 kΩ or higher
    B15-2 (#3) or D1-22 (#3) - Body ground
    10 kΩ or higher
    B15-5 (#4) or D1-21 (#4) - Body ground
    10 kΩ or higher
    B15-7 (INJF) or D1-25 (INJF) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4.CHECK INJECTOR DRIVER


    A099850E01
  1. Disconnect the B13 and B15 EDU connectors.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the wire harness side connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    B13-8 (+B) - B15-1 (GND)
    9 to 14 V



NG
CHECK EDU POWER SOURCE CIRCUIT
OK


5.CHECK ECM (INJECTOR VOLTAGE)


    A099851E01
  1. While idling the engine, check the waveform of the ECM connectors using an oscilloscope.

    Standard:
    Tester Connection
    Specified Condition
    D1-24 (#1) - D3-7 (E1)
    Correct waveform is shown
    D1-23 (#2) - D3-7 (E1)
    Correct waveform is shown
    D1-22 (#3) - D3-7 (E1)
    Correct waveform is shown
    D1-21 (#4) - D3-7 (E1)
    Correct waveform is shown
    D1-25 (INJF) - D3-7 (E1)
    Correct waveform is shown
    Tool Setting/(a)
    5 V/DIV., 20 msec./DIV.
    Tool Setting/(b)
    2 V/DIV., 20 msec./DIV.
    Condition
    Idling with warm engine

    HINT:
    The waveform varies depending on the injector injection.



NG
REPLACE ECM
OK

REPLACE INJECTOR DRIVER