Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    P0400/71    Exhaust Gas Recirculation Flow

for Preparation Click here


DESCRIPTION

The EGR system recirculates exhaust gases, and is controlled to the proper volume to be suitable for all driving conditions. The recirculated gas mixes with the intake air, allowing the EGR system to slow down engine combustion and lower the combustion temperature. This helps reduce NOx emissions.
In order to increase circulation efficiency, the ECM adjusts the lift amount of the EGR valve and throttle valve.

DTC No.
DTC Detection Condition
Trouble Area
P0400/71
  1. Difference between target and actual position of EGR valve is 10 % or more for 10 seconds or more
    (1 trip detection logic)
  2. Difference between target and actual position of EGR valve is 25 % or more for 3 seconds or more
    (1 trip detection logic)
  1. EGR valve stuck
  2. EGR valve does not move smoothly
  3. Open or short in E-VRV for EGR circuit
  4. Open or short in EGR valve position sensor circuit
  5. EGR valve position sensor
  6. Vacuum pump
  7. Vacuum hose connection loose
  8. ECM

HINT:
DTC detection is not performed for 4 seconds after brake switch is turned ON or OFF.


MONITOR DESCRIPTION

When the target and actual positions of the EGR valve are different, the ECM interprets this as a malfunction of the EGR valve and illuminates the MIL.

A093020E01


WIRING DIAGRAM


A110956E01


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.
  2. After warming up the engine, DTC P0400/71 is set 1 second or more after quickly accelerating the engine from idling.

1.CHECK OTHER DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / ECD/ DTC.

  1. Read DTCs.

    Result:

    Display (DTC output)
    Proceed to
    P0400/71
    A
    P0400/71 and P0405/96 and/or P0406/96
    B

    HINT:
    If any other codes besides DTC P0400/71 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2.CHECK VACUUM PUMP ASSEMBLY
  1. Check the negative pressure of the vacuum pump. (Click here)

    Standard:
    More than 86.7 kPa (650 mmHg, 26 in.Hg)



NG
REPLACE VACUUM HOSE ASSEMBLY
OK


3.CHECK VACUUM HOSES
  1. Check the vacuum hoses.

    OK:
    The hoses are not damaged and securely connected.



NG
REPAIR OR REPLACE VACUUM HOSE
OK


4.CHECK ECM TERMINAL VOLTAGE (EGR TERMINAL)


    G034909E01
  1. While idling the engine, check the waveform of the ECM connector.

    Standard:
    Tester Connection
    Specified Condition
    D3-9 (EGR) - D3-7 (E1)
    Correct waveform is shown
    Tool Setting
    2 V/DIV., 1 msec./DIV.
    Condition
    Idling with warm engine

    HINT:
    The waveform changes depending on the electric vacuum regulating valve for EGR operation.

    NOTICE:
    After replacing the ECM, the new ECM needs initialization (Click here).



NG
REPLACE ECM
OK


5.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY (E-VRV FOR EGR)


    A093008E01
  1. Disconnect the D55 E-VRV for EGR connector.

  1. Measure the resistance of the E-VRV.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    11 to 13 Ω



NG
REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
OK


6.CHECK HARNESS AND CONNECTOR (E-VRV FOR EGR - ECM)


    A099854E01
  1. Disconnect the D55 E-VRV for EGR connector.

  1. Disconnect the D3 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D55-2 - D3-9 (EGR)
    Below 1 Ω
    D55-2 or D3-9 (EGR) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (E-VRV FOR EGR - INTEGRATION RELAY)


    G034910E01
  1. Remove the integration relay from the engine room J/B.

  1. Disconnect the 1J integration relay connector.

  1. Disconnect the D55 E-VRV connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    1J-5 - D55-1
    Below 1 Ω
    1J-5 or D55-1 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


8.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY (EGR VALVE ASSEMBLY)
  1. Check the EGR valve assembly. (Click here)

    OK:
    The valve is not stuck and does not have heavy carbon deposits



NG
REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
OK

REPLACE ECM