Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    P0405/96    Exhaust Gas Recirculation Sensor "A" Circuit Low

DTC    P0406/96    Exhaust Gas Recirculation Sensor "A" Circuit High

for Preparation Click here


DESCRIPTION

The EGR valve position sensor is mounted on the EGR valve and used for detecting the lift amount of the valve. The lift amount detected by the sensor is provided to the ECM as feedback, the ECM then regulates the lift amount of the valve in accordance with engine running condition.

DTC No.
DTC Detection Condition
Trouble Area
P0405/96
EGR valve position sensor output voltage is less than 0.1 V for more than 5 seconds
(1 trip detection logic)
  1. Open or short in EGR valve position sensor circuit
  2. EGR valve position sensor
  3. ECM
P0406/96
EGR valve position sensor output voltage is more than 4.9 V for more than 5 seconds
(1 trip detection logic)
  1. Open or short in EGR valve position sensor circuit
  2. EGR valve position sensor
  3. ECM

HINT:
After confirming DTCs P0405/96 and P0406/96, check the EGR valve opening angle condition by entering the following menus on the intelligent tester : Power train / ECD / Engine / Data List / EGR Position.

Result
Condition
Changes between 0.3 V and 4.2 V
Normal
Less than 0.1 V
P0405/96 (Low input voltage)
More than 4.9 V
P0406/96 (High input voltage)

HINT:
The result values above are for when the ignition switch is ON (engine is stopped), or when the engine is fully warmed-up and idling.


MONITOR DESCRIPTION

When output voltage of the EGR valve position sensor deviates from the normal operating range of 0.1 to 4.9 V for more than 0.5 seconds, the ECM interprets this as a malfunction of the sensor circuit, and illuminates the MIL.
G039134E01

WIRING DIAGRAM


A110957E01


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.CHECK TERMINAL VOLTAGE (EGR VALVE POSITION SENSOR CONNECTOR)


    A085350E01
  1. Disconnect the D52 sensor connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    D52-1 (VC) - D52-2 (D52)
    4.5 to 5.5 V



NG
Go to step 3
OK


2.INSPECT EGR VALVE POSITION SENSOR
  1. Check the EGR valve position sensor. (Click here)

    Standard resistance:
    Tester connection
    EGR valve condition
    Spesified Condition
    VC(1) - D52(2)
    -
    4 to 6 kΩ at 20°C (68°F)
    EGLS(3) - D52(2)
    Fully opened
    3.9 kΩ at 20°C (68°F)
    EGLS(3) - D52(2)
    Fully closed
    1.0 kΩ at 20°C (68°F)



NG
REPLACE EGR VALVE ASSEMBLY
OK


3.CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)


    G034912E01
  1. Disconnect the D52 sensor connector.

  1. Disconnect the D3 and D1 ECM connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D52-3 (EGLS) - D3-33 (EGLS)
    Below 1 Ω
    D52-2 (D52) - D1-28 (D52)
    Below 1 Ω
    D52-3 (EGLS) or D3-33 (EGLS) - Body ground
    10 kΩ or higher
    D52-2 (D52) or D1-28 (D52) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM