Home › STEERING › STEERING COLUMN › STEERING COLUMN ASSEMBLY

STEERING COLUMN ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM BATTERY NEGATIVE TERMINAL

NOTICE:
Wait for 90 seconds after disconnecting the cable to prevent the airbag working.



2. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


3. REMOVE STEERING PAD (W/O AIRBAG)


    C106047E01
  1. Remove the screw.

  1. Remove the steering pad.

  1. Disconnect the horn connector.



4. REMOVE STEERING WHEEL COVER LOWER NO.2 (W/ AIRBAG)
  1. Using a screwdriver, remove the steering wheel No.2 cover lower.

    HINT:
    Tape up the screwdriver tip before use.



5. REMOVE STEERING WHEEL COVER LOWER NO.3 (W/ AIRBAG)
  1. Using a screwdriver, remove the steering wheel No.3 cover lower.

    HINT:
    Tape up the screwdriver tip before use.



6. REMOVE STEERING PAD (W/ AIRBAG)


    C106057E01
  1. Using a "torx" socket wrench (T30), loosen the 2 "torx" screws until the groove along the screw circumference catches on the screw case.

  1. Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand.

  1. Disconnect the horn connector.



    C106058
  1. Disconnect the connector and remove the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



7. REMOVE STEERING WHEEL ASSEMBLY
  1. Remove the steering wheel set nut.

  1. Put matchmarks on the steering wheel assembly and steering main shaft assembly.



    C106843E01
  1. Using SST, remove the steering wheel assembly.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



8. REMOVE STEERING COLUMN COVER LOWER
  1. Set the steering tilt mechanism to the lowermost position.



    C106844
  1. Remove the 2 "torx" screws from the steering column cover lower.



    F047992E01
  1. Press on the left side of the steering column cover lower to disengage claw A.



    C106845
  1. Press on the right side of the steering column cover lower to disengage claw B.

    HINT:
    If it is difficult to disengage claw B, enlarge the clearance downward on the left side of the steering column cover lower to disengage the claw.

    Twist the steering column cover lower by pulling it downward.

    NOTICE:
    Be sure to pull the steering column cover lower downward to prevent damage to the claw.



9. REMOVE INSTRUMENT PANEL FINISH PANEL LOWER


    B102827E01
  1. Using a clip remover, remove the 2 clips (A).

  1. Disengage the 4 clips (B).

  1. Disconnect the connector.



    B102838
  1. Push the positions indicated by the arrows in the illustration to separate the fuel lid lock control cable and bonnet (hood) control cable assembly from the panel.
    Remove the instrument panel finish lower.



10. REMOVE STEERING INTERMEDIATE SHAFT


    C102130
  1. Remove the 3 bolts and the steering shaft cover.



    C102131E01
  1. Remove the bolt.

  1. Slide the steering intermediate shaft assembly No.2 and put matchmarks on the steering gear assembly and the steering intermediate shaft assembly No.2.



11. REMOVE STEERING COLUMN ASSEMBLY
  1. Disconnect the connectors and wire harness clamps from the steering column assembly.



  1. Remove the 3 bolts and the steering column assembly.


    C106048E01



12. REMOVE HORN CONTACT PLATE (W/O AIRBAG)


    C106049
  1. Disengage the 3 claws and remove the horn contact plate.



13. REMOVE STEERING COLUMN COVER UPPER


14. REMOVE SPIRAL CABLE ASSEMBLY (W/ AIRBAG)
  1. Lock the shift lever at the lowest position.

  1. Disengage the claws and slide the steering column upper cover upward.

    HINT:
    Do not remove the steering column upper cover.

  1. Disconnect the connectors from the spiral cable.



    C113668E01
  1. Disengage the 3 claws and remove the spiral cable.



15. REMOVE WIPER SWITCH


    E103129E01
  1. Disconnect the connector.

  1. Disengage the claw and remove the wiper switch as shown in the illustration.

    NOTICE:
    If the claw is pushed with excessive force, it may be broken.

    HINT:
    Slide the steering column cover upper upward to remove the wiper switch.



16. REMOVE HEADLIGHT DIMMER SWITCH


    E103535E01
  1. Disconnect the connector.

  1. Disengage the claw and remove the headlight dimmer switch as shown in the illustration.

    NOTICE:
    If the claw is pushed with excessive force, it may be broken.

    HINT:
    Slide the steering column upper cover upward to remove the headlight dimmer switch.