PARKING BRAKE LEVER > INSTALLATION |
| 1. INSTALL PARKING BRAKE CONTROL HANDLE ASSEMBLY (LHD) |
Pass the parking brake cable assembly No.1 out of the cabin.
![]() |
Install the parking brake cable assembly No.1 to the body with the 2 bolts.
![]() |
Install the parking brake control handle to the body with the 2 nuts.
![]() |
Return the parking brake control handle to its initial position.
![]() |
Install the parking brake control handle with the 2 bolts.
![]() |
Connect the parking brake switch assembly.
Apply MP grease to the connecting part of the parking brake cable assembly No.1 and the parking brake intermediate lever.
Install the parking brake cable assembly No.1 to the parking brake intermediate lever. (Procedure B)
Install the clamps to the parking brake cable assembly No.1.
Install the parking brake cable assembly No.1 to the body with the 4 bolts. (Procedure A)

| 2. INSTALL PARKING BRAKE CONTROL HANDLE SUB-ASSEMBLY (RHD) |
Pass the parking brake cable assembly No.1 from the driver side to the passenger side, then out of the cabin.
![]() |
Install the parking brake cable assembly No.1 to the body with the 2 bolts.
![]() |
Install the parking brake control handle to the body with the 2 nuts.
![]() |
Return the parking brake control handle to its initial position.
![]() |
Install the parking brake control handle with the 2 bolts.
![]() |
Connect the parking brake switch assembly.
Apply MP grease to the connecting part of the parking brake cable assembly No.1 and the parking brake intermediate lever.
Install the parking brake cable assembly No.1 to the parking brake intermediate lever. (Procedure B)
Install the clamps to the parking brake cable assembly No.1.
Install the parking brake cable assembly No.1 to the body with the 4 bolts. (Procedure A)

| 3. REMOVE INSTRUMENT PANEL TO FLOOR BRACE SUB-ASSEMBLY (LHD) |
| 4. INSTALL PARKING BRAKE HOLE COVER |
![]() |
Engage the 6 claws and install the parking brake hole cover.
| 5. INSTALL INSTRUMENT PANEL UNDER COVER ASSEMBLY NO.1 |
![]() |
Engage the 3 claws.
Install the instrument panel No.1 under cover sub-assembly with the 2 clips.
| 6. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER |
![]() |
Engage the 4 clips (B).
Install the instrument panel finish panel lower with the 2 clips (A).
| 7. INSTALL ENGINE UNDER COVER NO.2 |
| 8. INSTALL ENGINE UNDER COVER NO.1 |
| 9. INSPECT PARKING BRAKE CONTROL HANDLE TRAVEL |
Pull firmly on the parking brake control handle.
Release the parking brake lock, and return the parking brake control handle to its off position.
Slowly pull the parking brake control handle all the way up, and count the number of clicks.
| 10. REMOVE REAR WHEEL |
| 11. ADJUST REAR BRAKE SHOE CLEARANCE |
![]() |
Using a screwdriver from a service hole, turn the adjuster to expand the shoes so that the brake shoes touch the brake drum.
![]() |
Using another screwdriver, push up the automatic adjust lever and turn the adjuster to contract the shoes so that the brake shoe does not touch the brake drum. Then turn the adjuster another 180 degrees to further contract the shoes.
Install the hole plug.
| 12. INSTALL REAR WHEEL |
| 13. ADJUST PARKING BRAKE CONTROL HANDLE TRAVEL |
Lift the vehicle
![]() |
Depress the parking brake handle. Hold the parking brake adjusting nut using a wrench, and loosen the lock nut.
Turn the parking brake adjusting nut until the parking brake handle travel meets the above specification.
Count the number of clicks after depressing and releasing the parking brake control handle 3 or 4 times.
Check whether the parking brake drags or not.
When operating the parking brake control handle, check that the parking brake indicator light comes on.
Hold the parking brake adjusting nut using a wrench, and tighten the lock nut.
Lower the vehicle.