Home › BRAKE › PARKING BRAKE › PARKING BRAKE CABLE

PARKING BRAKE CABLE > INSTALLATION

for Preparation Click here



1. INSTALL PARKING BRAKE CABLE ASSEMBLY NO.3 (NARROW BODY)
  1. Install the parking brake cable assembly No.3 to the parking brake equalizer.



  1. Install the parking brake cable assembly No.3 with the 5 bolts and the nut.

    Torque:
    14.5 N*m{ 148 kgf*cm , 11 ft.*lbf }



    C102158



    C102159
  1. Install the parking brake cable assembly No.3 to the backing plate with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



2. INSTALL PARKING BRAKE CABLE ASSEMBLY NO.3 (WIDE BODY)
  1. Install the parking brake cable assembly No.3 to the parking brake equalizer.



  1. Install the parking brake cable assembly No.3 with the 6 bolts and the nut.

    Torque:
    14.5 N*m{ 148 kgf*cm , 11 ft.*lbf }



    C105462



    C102159
  1. Install the parking brake cable assembly No.3 to the backing plate with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



3. APPLY HIGH TEMPERATURE GREASE


    C102609E01
  1. Apply high temperature grease to the shoe attached surface of the backing plate.



4. INSTALL REAR BRAKE SHOE


    C102607E01
  1. Using pliers, install the rear brake shoe, shoe strut set, rear cushion lever and shoe lever with a new C-washer.



    C102606
  1. Connect the parking brake cable No.3 to the front brake shoe.



    C102603E01
  1. Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down cup.

    SST
    09718-00010  



5. INSTALL FRONT BRAKE SHOE
  1. Install the return spring to each brake shoe.



    C102604E01
  1. Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down cup.

    SST
    09718-00010  



    C102667
  1. Install the brake shoe lower strut.

    NOTICE:
    Make sure that the shoe lower strut and brake rear cushion lever are securely engaged.



    C102600
  1. Using needle-nose pliers, install the tension spring.



6. CONNECT PARKING BRAKE SHOE STRUT SET


    C102599E01
  1. Using SST, install the upper side tension spring.

    SST
    09703-30011  



7. INSTALL AUTOMATIC ADJUST LEVER


    C102605
  1. Install the automatic adjust lever and tension spring.

    NOTICE:
    Make sure to install the automatic adjust lever between the groove of the shoe strut set and brake shoe.



8. INSTALL REAR AXLE BRAKE DRUM GASKET


9. INSTALL REAR BRAKE DRUM


10. INSPECT PARKING BRAKE CONTROL HANDLE TRAVEL
  1. Pull firmly on the parking brake control handle.

  1. Release the parking brake lock, and return the parking brake control handle to its off position.

  1. Slowly pull the parking brake control handle all the way up, and count the number of clicks.

    Parking brake control handle travel:
    10 to 16 clicks at 200 N (20 kgf, 44 lbf)

    HINT:
    1. If the number of clicks falls outside of the specified range, release the parking brake lock and adjust it.
    2. If there are fewer clicks than the specified value, loosen the parking brake wire adjustment nut an the lock nut. With the parking brake cable loosened, adjust the clearance between the brake drum and lining.



11. REMOVE REAR WHEEL


12. ADJUST REAR BRAKE SHOE CLEARANCE


    C102598E01
  1. Using a screwdriver from a service hole, turn the adjuster to expand the shoes so that the brake shoes touch the brake drum.



    C102597E01
  1. Using another screwdriver, push up the automatic adjust lever and turn the adjuster to contract the shoes so that the brake shoe does not touch the brake drum. Then turn the adjuster another 180 degrees to further contract the shoes.

  1. Install the hole plug.



13. INSTALL REAR WHEEL

Torque:
100 N*m{ 1,020 kgf*cm , 74 ft.*lbf }



14. ADJUST PARKING BRAKE CONTROL HANDLE TRAVEL
  1. Lift the vehicle



    C102142E01
  1. Depress the parking brake handle. Hold the parking brake adjusting nut using a wrench, and loosen the lock nut.

  1. Turn the parking brake adjusting nut until the parking brake handle travel meets the above specification.

    Parking brake control handle travel:
    10 to 16 clicks at 200 N (20 kgf, 44 lbf)

  1. Count the number of clicks after depressing and releasing the parking brake control handle 3 or 4 times.

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake control handle, check that the parking brake indicator light comes on.

    Standard:
    Brake warning light always comes on at the first click.

  1. Hold the parking brake adjusting nut using a wrench, and tighten the lock nut.

    Torque:
    14.5 N*m{ 148 kgf*cm , 11 ft.*lbf }

  1. Lower the vehicle.