Home › BODY ELECTRICAL › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM

WIRELESS DOOR LOCK CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (BODY ECU)

E107676E02

  1. Disconnect the 5E, 5G and 5M connectors.

  2. Check the voltage between each terminal of the wire harness side connectors and body ground.

    Voltage: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    ECUB (5E-17) - Body ground
    W-R - Body ground
    Body ECU power supply
    Always
    10 to 14 V
    ALTB (5G-1) - Body ground
    B-G - Body ground
    Power door lock motor power supply
    Always
    10 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Check the resistance between each terminal of the wire harness side connectors and the body ground.

    Resistance: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND (5E-12) - Body ground
    W-B - Body ground
    Ground circuit
    Always
    Below 1 Ω
    GND (5M-7) - Body ground
    W-B - Body ground
    Ground circuit
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  4. Reconnect the 5E, 5G and 5M connectors.

  5. Check the voltage between terminals of the instrument panel junction block assembly (body ECU) side connectors.

    Voltage: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    RCTY (5A-9) - GND (5E-12)
    W - W-B (*1)
    G - W-B (*2)
    Back door courtesy light switch circuit
    Back door is open → closed
    Below 1 V → 10 to 14 V
    RCTY (5A-18) - GND (5E-12)
    W - W-B
    Rear door (RH) courtesy light switch circuit
    Rear door (RH) is open → closed
    Below 1 V → 10 to 14 V
    RCTY (5A-30) - GND (5E-12)
    W - W-B
    Rear door (LH) courtesy light switch circuit
    Rear door (LH) is open → closed
    Below 1 V → 10 to 14 V
    PCTY (5E-10 ) - GND (5E-12)
    R-L - W-B (*3)
    R-G - W-B (*4)
    Front passenger side door courtesy light switch circuit
    Front passenger side door is open → closed
    Below 1 V → 10 to 14 V
    DCTY (5E-27) - GND (5E-12)
    R-G - W-B (*3)
    R-L - W-B (*4)
    Driver side door courtesy light switch circuit
    Driver side door is open → closed
    Below 1 V → 10 to 14 V
    KSW (5H-14) - GND (5E-12)
    Y - W-B
    Key unlock warning switch circuit
    Ignition key is inserted → not inserted
    Below 1 V → 10 to 14 V
    HAZ (5S-17) - GND (5E-12)
    G-W - W-B
    Turn signal flasher relay circuit
    Either of transmitter switches is pressed → released
    Below 1 V (*5) → 10 to 14 V
    PRG (H7-6) - GND (5E-12)
    B - W-B
    Door control receiver communication circuit
    Ignition switch on and the wireless door lock system is operated
    Pulse generation
    RDA (H7-7) - GND (5E-12)
    W - W-B
    Door control receiver communication circuit
    Ignition switch on and the wireless door lock system is operated
    Pulse generation

If the result is not as specified, the instrument panel junction block assembly (body ECU) may have a malfunction.

HINT:
  1. *1: 6 Speakers
  2. *2: Except *1
  3. *3: LHD
  4. *4: RHD
  5. *5: When operating the answer back function


DOOR CONTROL RECEIVER


    E105247E01
  1. Disconnect the Y2 connector.

  2. Check the voltage between the terminal of the wire harness side connector and the body ground.

    Voltage: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    +B (Y2-5) - Body ground
    O - Body ground
    Door control receiver power supply
    Always
    10 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Check the resistance between the terminal of the wire harness side connector and the body ground.

    Resistance: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND (Y2-1) - Body ground
    W-B - Body ground
    Ground circuit
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  4. Reconnect the Y2 connector.

  5. Check the voltage between each terminal of the door control receiver side connector.

    Voltage: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    RDA (Y2-2) - GND (Y2-1)
    G - W-B
    Door control receiver communication circuit
    Ignition switch on and the wireless door lock system is operated
    Pulse generation
    PRG (Y2-3) - GND (Y2-1)
    GR - W-B
    Door control receiver communication circuit
    Ignition switch on and the wireless door lock system is operated
    Pulse generation