Home › BRAKE › BRAKE › FRONT BRAKE

FRONT BRAKE > DISASSEMBLY

for Preparation Click here



1. REMOVE FRONT DISC BRAKE PAD KIT
  1. Remove the 2 brake pads with anti-squeal shims.



2. REMOVE FRONT DISC BRAKE ANTI SQUEAL SHIM KIT
  1. Remove the 4 anti-squeal shims from the brake pad.

  1. Remove the pad wear indicator from each pad.



3. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE


4. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE


5. REMOVE FRONT DISC BRAKE CYLINDER SLIDE PIN
  1. Remove the cylinder slide pin from the cylinder mounting.



6. REMOVE FRONT DISC BRAKE CYLINDER SLIDE BUSH


    C102588E01
  1. Using a screwdriver, remove the cylinder slide bush from the cylinder slide pin.

    HINT:
    Tape the screwdriver tip before use.



7. REMOVE FRONT DISC BRAKE CYLINDER SLIDE PIN NO.2
  1. Remove the cylinder slide pin No.2 from the cylinder mounting.



8. REMOVE FRONT DISC BRAKE CYLINDER MOUNTING
  1. Remove the 2 bolts and cylinder mounting.



9. REMOVE BUSH DUST BOOT NO.1
  1. Secure the cylinder mounting in a vise.



    C102589
  1. Using a screwdriver and a plastic hammer, remove the 2 bush dust boots.



10. REMOVE CYLINDER BOOT


    C102590
  1. Using a screwdriver, remove the set ring.

    NOTICE:
    Do not damage the inner cylinder or cylinder groove.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the cylinder boot.



11. REMOVE FRONT DISC BRAKE PISTON


    C102591
  1. Place a shop rag or a piece of cloth between the piston and the disc brake cylinder assembly.

  1. Use compressed air to remove the piston from the disc brake cylinder assembly.

    CAUTION:
    Do not place your fingers in front of the piston when using compressed air.

    NOTICE:
    Do not spatter the brake fluid.



12. REMOVE PISTON SEAL


    C102592
  1. Using a screwdriver, remove the piston seal from the disc brake cylinder assembly.

    HINT:
    Tape the screwdriver tip before use.



13. REMOVE FRONT DISC BRAKE BLEEDER PLUG CAP


14. REMOVE FRONT DISC BRAKE BLEEDER PLUG


15. SEPARATE FRONT SPEED SENSOR


    C102281E01
  1. Remove the 2 bolts, and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Be careful not to damage the speed sensor.
    2. Prevent foreign matter from adhering to the speed sensor.



16. SEPARATE TIE ROD END SUB-ASSEMBLY
  1. Remove the cotter pin and castle nut.



    C102285E01
  1. Using SST, separate the tie rod end from the steering knuckle.

    SST
    09628-00011  

    NOTICE:
    1. Do not damage the ball joint dust boot.
    2. Do not damage the brake dust cover.
    3. Make sure that the string of the SST is securely tied to the vehicle.



17. REMOVE FRONT AXLE ASSEMBLY


    C102287
  1. Remove the 4 bolts, 4 nuts and front axle assembly from the front suspension lower arm.

  1. Remove the cotter pin and castle nut.



    C102660E01
  1. Using SST, remove the front axle assembly from the front suspension upper arm.

    SST
    09628-62011  

    NOTICE:
    1. Do not damage the ball joint dust boot.
    2. Apply grease to the threads and tip of the SST center bolt before use.
    3. Make sure that the string of the SST is securely tied to the vehicle.



18. REMOVE FRONT LOWER BALL JOINT ASSEMBLY
  1. Fix the steering knuckle in the vise using aluminium plates.

    NOTICE:
    Do not damage the steering knuckle.

  1. Remove the cotter pin.

  1. Loosen the nut.



    C103882E01
  1. Use SST to separate the front lower ball joint assembly from the steering knuckle.

    SST
    09628-62011  

    NOTICE:
    1. Do not damage the ball joint dust boot.
    2. Apply grease to the threads and tip of the SST center bolt before use.

  1. Remove the nut and front lower ball joint assembly.



19. REMOVE STEERING KNUCKLE


    C103883E01
  1. Remove the 4 bolts.



    C103880E01
  1. Using SST, remove the steering knuckle, brake dust cover from the front axle hub sub-assembly.

    SST
    09950-40011   (09951-04020, 09953-04010, 09952-04010, 09955-04051)

    NOTICE:
    Apply grease to the threads and tip of the SST center bolt (09953-04010) before use.



20. REMOVE FRONT DISC


    C102293E01
  1. Remove the 6 bolts.



    C113549E01
  1. Remove the front disc as shown in the illustration.