FRONT BRAKE > REASSEMBLY |
| 1. INSTALL FRONT DISC |
![]() |
Install the front disc as shown in the illustration.
![]() |
Install the front disc with the 6 bolts.
| 2. INSTALL FRONT LOWER BALL JOINT ASSEMBLY |
Fix the steering knuckle in the vise using aluminium plates.
Install the front lower ball joint assembly to the steering knuckle with the nut.
Install a new cotter pin to the front lower ball joint assembly.
| 3. INSTALL STEERING KNUCKLE |
![]() |
Install the steering knuckle and brake dust cover to the front axle hub sub-assembly with the 4 bolts.
| 4. INSTALL FRONT AXLE ASSEMBLY |
Temporarily install the front axle assembly to the front suspension upper arm and front suspension lower arm.
![]() |
Fully tighten front suspension lower arm with the 4 bolts and 4 nuts.
![]() |
Fully tighten the front suspension upper arm with the nut.
Install a new cotter pin to the front suspension upper arm.
| 5. INSTALL TIE ROD END SUB-ASSEMBLY |
Install the tie rod end sub-assembly to the steering knuckle with the castle nut.
Install a new cotter pin to the tie rod end sub-assembly.
| 6. INSTALL FRONT SPEED SENSOR |
![]() |
Install the speed sensor to the steering knuckle with the 2 bolts.
| 7. INSPECT DISC RUNOUT |
![]() |
Using a dial indicator, measure the disc runout 10 mm (0.39 in.) away from the outer edge of the disc.
If the runout exceeds the maximum value, change the installation positions of the disc and axle so that the runout will become minimal. If the runout still exceeds the maximum, check the bearing play in the axial direction and the axle hub runout . If the bearing play and the axle hub runout are normal and that the disc thickness is not within the specified range, grind the disc. If the disc thickness is less than the minimum, replace the disc.
| 8. TEMPORARILY TIGHTEN FRONT DISC BRAKE BLEEDER PLUG |
| 9. INSTALL FRONT DISC BRAKE BLEEDER PLUG CAP |
| 10. INSTALL PISTON SEAL |
Apply lithium soap base glycol grease to a new piston seal.
Install the piston seal to the disc brake cylinder assembly.
| 11. INSTALL FRONT DISC BRAKE PISTON |
![]() |
Apply lithium soap base glycol grease to the piston and a new cylinder boot.
Install the cylinder boot to the piston.
Install the piston to the disc brake cylinder assembly.
| 12. INSTALL CYLINDER BOOT |
![]() |
Install the cylinder boot to the disc brake cylinder assembly.
Using a screwdriver, install a new set ring.
| 13. INSTALL BUSH DUST BOOT NO.1 |
Secure the cylinder mounting in a vise.
![]() |
Apply lithium soap base glycol grease to the seal surface of 2 new bush dust boots.
Using a socket wrench (21 mm) and a hammer, install the 2 bush dust boots.
| 14. INSTALL FRONT DISC BRAKE CYLINDER MOUNTING |
Install the cylinder mounting with the 2 bolts.
| 15. INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN NO.2 |
Apply lithium soap base glycol grease to the sliding part and the seal surface of the cylinder slide pin No.2.
Install the cylinder slide pin No.2 to the cylinder mounting.
| 16. INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSH |
![]() |
Apply lithium soap base glycol grease to the contact surface of the new cylinder slide bush and the cylinder slide pin.
Install the cylinder slide bush to the cylinder slide pin.
| 17. INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN |
Install the cylinder slide pin to the cylinder mounting.
| 18. INSTALL FRONT DISC BRAKE CYLINDER MOUNTING |
| 19. INSTALL FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT |
![]() |
Apply disc brake grease to the 2 anti-squeal shims No.1 and install them to each pad.
Install the 3 anti-squeal shims to each pad.
Install the 2 pad wear indicator plates to the pads.
| 20. INSTALL FRONT DISC BRAKE PAD KIT |
Install the 2 pads with pad wear indicator plates to the cylinder mounting.