AIR CONDITIONING UNIT > INSTALLATION |
| 1. INSTALL AIR CONDITIONING RADIATOR ASSEMBLY |
![]() |
Install the air conditioning radiator assembly with the 3 screws.
![]() |
w/ PTC
Install the wire harness with the screw.
| 2. INSTALL AIR DUCT NO.2 |
![]() |
Engage the 2 claws to install the air duct No.2.
| 3. INSTALL AIR CONDITIONER UNIT ASSEMBLY |
Install the air conditioner unit assembly with the 3 bolts.

| 4. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY |
Driver seat:
Using a "Torx" socket wrench (T40), install the instrument panel reinforcement assembly with the 2 Torx bolts.
Passenger seat:
Using a hexagon wrench 12 mm, install the instrument panel reinforcement assembly with the 2 bolts.
Using a "Torx" socket wrench (T40), install the instrument panel reinforcement assembly with the 2 "Torx" bolts.

Install the 2 bolts and nut. (AUTOMATIC TRANSMISSION)
Install the 3 bolts and nut. (MANUAL TRANSMISSION)
Install the 2 bolts and cap.
| 5. INSTALL INSTRUMENT PANEL ASSEMBLY |
| 6. INSTALL COOLER REFRIGERANT LIQUID PIPE B |
Remove the attached vinyl tape from the pipe.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler refrigerant liquid pipe B.
Install the O-ring on the cooler refrigerant liquid pipe B.
Install the cooler refrigerant liquid pipe B.
| 7. INSTALL COOLER REFRIGERANT SUCTION PIPE A |
Remove the attached vinyl tape from the hose.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler refrigerant suction pipe A.
Install the O-ring on the cooler refrigerant suction pipe A.
Move the hook connector in the direction indicated by the arrow in the illustration.
![]() |
Insert the pipe joints into the fitting holes securely and tighten the bolt.
| 8. INSTALL INTERCOOLER ASSEMBLY (w/ Intercooler) |
![]() |
Temporarily install the intercooler assembly with the 3 bolts.
Connect the air hose No.2, and tighten the clamp.
Connect the air hose No.3, and tighten the clamp.
Tighten the intercooler assembly.
| 9. INSTALL RADIATOR SUPPORT SUB-ASSEMBLY (w/ Intercooler) |
![]() |
Install the radiator upper support with the 6 bolts and 2 screws.
| 10. INSTALL HOOD LOCK ASSEMBLY (w/ Intercooler) |
Connect the hood lock cable assembly to the hood lock assembly.
![]() |
Temporarily tighten the hood lock assembly with the 3 bolts from the radiator upper support.
![]() |
Check the hood position and adjust the hood lock assembly position.
Tighten the hood lock assembly with the 3 bolts.
| 11. INSTALL RADIATOR RESERVE TANK ASSEMBLY (w/ Intercooler) |
Connect the water by-pass hose No.2 with the clip.
Connect the water by-pass hose No.1 with the clip.
![]() |
Place the reserve tank in the 2 grommets of the radiator upper support, and install the radiator reserve tank assembly with the bolt.
| 12. INSTALL WINDSHIELD WASHER JAR ASSEMBLY (w/ Rear Wiper and Intercooler) |
Connect the 2 connectors and 2 hoses.
![]() |
Install the wind washer jar assembly with the 2 bolts.
| 13. INSTALL WINDSHIELD WASHER JAR ASSEMBLY (w/o Rear Wiper and w/ Intercooler) |
Connect the connector and hose.
![]() |
Install the wind washer jar assembly with the 2 bolts.
| 14. INSTALL WINDSHIELD WASHER FLUID (w/ Intercooler) |
| 15. INSTALL AIR INLET DUCT (w/ Intercooler) |
![]() |
Install the air inlet duct No.1 with the 2 bolts and 2 clips.
Install the air inlet duct No.2 with the 3 clips.
| 16. INSTALL RADIATOR GRILLE (w/ Intercooler) |
| 17. INSTALL ENGINE UNDER COVER NO.1 (w/ Intercooler) |
| 18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 19. ADD ENGINE COOLANT (2KD-FTV Type:) |
Firmly tighten the drain plugs and fill the radiator reserve tank assembly with coolant to the top of the inlet.
Loosen the bleeder plug of outlet housing.
When air is bled and the coolant drains out, firmly install the bleeder plug.
Add coolant up to the B line mark in the radiator reserve tank assembly and install the radiator cap.
| Condition | Capacity |
| w/ rear heater | 17.0 liters (18.0 US qts, 15.0 imp. qts) |
| w/o rear heater | 15.0 liters (15.9 US qts, 13.2 imp. qts) |
Warm up the engine.
After the engine cools down check that the coolant level is between the LOW and FULL level marks.
| 20. ADD ENGINE COOLANT (2TR-FE Type:) |
Firmly tighten the drain plugs and fill the reservoir tank with coolant to the top of the inlet.
Remove the 2-way that is located near the throttle body.
When air is bled and the coolant drains out, firmly install the 2-way.
Add coolant up to the B line mark in the reservoir tank and install the radiator cap.
| Condition | Capacity |
| w/ rear heater | 15.0 liters (15.8 US qts, 13.2 lmp. qts) |
| w/o rear heater | 13.0 liters (13.7 US qts, 11.4 lmp. qts) |
Warm up the engine.
After the engine cools down, check that the coolant level is between the LOW and FULL level marks.
| 21. ADD ENGINE COOLANT (5L-E Type:) |
Close the engine drain plug.
Close the radiator drain cock plug.
Slowly fill the cooling system with coolant.
Slowly pour coolant into the radiator reserve tank until it reaches the FULL line.
Install the radiator cap to the radiator reserve tank.
Press the inlet and outlet radiator hoses several times by hand while warming up the engine.
Stop the engine, and wait until the engine coolant cools down.
Add coolant to the FULL line of the radiator reservoir.
| 22. CHARGE REFRIGERANT |
Perform vacuum purging using a vacuum pump.
Charge with refrigerant HFC-134a (R134a).

| 23. WARM UP ENGINE |
Warm up the engine at less than 1,850 rpm for 2 minutes or more after charging refrigerant.
| 24. REMOVE CHECK FOR ENGINE COOLANT LEAKS (2KD-FTV Type:) |
Fill the radiator with coolant and attach a radiator cap tester to the radiator.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 137 kPa (1.4 kgf/cm2, 19.9 psi), and check that the pressure does not drop.
| 25. REMOVE CHECK FOR ENGINE COOLANT LEAKS (2TR-FE Type:) |
Fill the radiator with coolant and attach a radiator cap tester to the radiator.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 137 kPa (1.4 kgf/cm2, 19.9 psi), and check that the pressure does not drop.
| 26. REMOVE CHECK FOR ENGINE COOLANT LEAKS (5L-E Type:) |
Fill the radiator with coolant and attach a radiator cap tester to the radiator.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17.1 psi), and check that the pressure does not drop.
| 27. CHECK FOR LEAKAGE OF REFRIGERANT |
After recharging refrigerant gas, check for leakage of refrigerant gas using a halogen leak detector.
Carry out the test under the following conditions:
![]() |
Using a gas leak detector, check for leakage of the refrigerant line.
![]() |
Bring the gas leak detector close to the drain hose with the detector's power off.
If a gas leak is not detected on the drain hose, remove the blower motor control from the cooling unit. Insert the gas leak detector sensor into the unit and perform the test.
Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.
| 28. PERFORM INITIALIZATION |