Home › SUSPENSION & AXLE › SUSPENSION › TORSION BAR SPRING

TORSION BAR SPRING > INSTALLATION

for Preparation Click here



1. INSTALL FRONT SUSPENSION TORQUE ARM


    C101961E01
  1. Install the front suspension torque arm to the suspension upper arm with the 2 bolts.

    Torque:
    81 N*m{ 826 kgf*cm , 60 ft.*lbf }



2. TEMPORARILY TIGHTEN TORSION BAR SPRING


    C101964
  1. Check the right-left identification on the rear ends of the torsion bar springs.

    NOTICE:
    The end with an identification mark must be installed to the rear of the vehicle.

  1. Wrap the splines on both ends of the torsion bar spring with protective tape.

  1. Install the torsion dust cover to the torsion bar spring.

    NOTICE:
    Do not damage the lip of the dust cover when installing.



    C103220E02
  1. Remove the protective tape from the spline on both ends of the torsion bar spring and apply MP grease No.2 to them.



    C101959E01
  1. Align the matchmarks on the torsion bar spring and torque arm and engage the splines (for anchor arm side).

  1. Align the matchmarks on the torsion bar spring and anchor arm and engage the splines (for torque arm side).



    C103229E03
  1. Install the following parts to the anchor arm.

    1. Anchor arm swivel. (Part A)

    2. Anchor arm adjusting hexagon bolt. (Part B)

    3. Anchor arm adjusting seat. (Part C)

    4. Anchor arm adjust nut. (Part D)



    C101960E01
  1. Tighten the anchor arm adjust nut so that the protrusion length of the thread of the anchor arm adjusting hexagon bolt equals the length of dimension A in the table below.

    HINT:
    Australia:
    Model
    A
    (mm (in. ) )
    TRH201R-RBMDKQ
    51.4
    (2.02)
    TRH201R-RBPDKQ
    51.4
    (2.02)
    TRH221R-MBMDKQ
    53.9
    (2.12)
    TRH221R-MBPDKQ
    54
    (2.12)
    TRH223R-LEMDKQ
    53.8
    (2.12)
    TRH223R-LEPDKQ
    53.7
    (2.11)
    KDH200R-RBMDYQ
    50.2
    (1.98)
    KDH200R-RBPDYQ
    50.3
    (1.98)
    KDH220R-MBMDYQ
    56.3
    (2.22)
    KDH220R-MBPDYQ
    56.3
    (2.22)
    KDH222R-LEMDYQ
    56.8
    (2.24)
    KDH222R-LEPDYQ
    56.9
    (2.24)
    South Africa:
    Model
    A
    TRH201R-RBMDKQ
    51.6
    (2.03)
    TRH221R-MBMDKQ
    53.9
    (2.12)
    TRH223R-LEMDKQ
    54
    (2.12)
    KDH200R-RBMDYQ
    50.5
    (1.99)
    KDH220R-MBMDYQ
    56.4
    (2.22)
    KDH222R-LEMDYQ
    57.2
    (2.25)
    New Zealand:
    Model
    A
    (mm (in. ) )
    TRH223R-LEMDKQ
    52.5
    (2.07)
    KDH222R-LEMDYQ
    55.4
    (2.18)
    KDH222R-LEPDYQ
    55.4
    (2.18)
    TRH201R-SRMDK
    50.4
    (1.98)
    TRH201R-SRPDK
    50.6
    (1.99)
    KDH200R-SRMDY
    49.9
    (1.96)
    KDH200R-SRPDY
    50.4
    (1.98)
    KDH220R-LFMDY
    53.7
    (2.11)
    KDH220R-LFPDY
    53.8
    (2.12)
    Thailand:
    Model
    A
    (mm (in. ) )
    KDH200R-RBMDY
    49.4
    (1.94)
    TRH213R-KDPNK
    50.7
    (2.00)
    KDH202R-RDMDY
    50.2
    (1.98)
    KDH202R-RDMNY
    47.1
    (1.85)
    KDH222R-LEMDY
    58.4
    (2.30)
    Singapore:
    Model
    A
    (mm (in. ) )
    KDH200R-RBPDY
    46.9
    (1.85)
    KDH200R-SBMDY
    47
    (1.85)
    KDH202R-REMDY
    47.1
    (1.85)
    China:
    Model
    A
    (mm (in. ) )
    TRH213L-JDMNK
    53.6
    (2.11)
    TRH223L-LEMNK
    54.1
    (2.13)
    TRH223L-LEPNK
    54.1
    (2.13)
    the Philippines:
    Model
    A
    (mm (in. ) )
    KDH202L-REMDY
    50.5
    (1.99)
    KDH212L-JDMNY
    59.0
    (2.32)
    GCC countries (*1):
    Model
    A
    (mm (in. ) )
    TRH201L-SBMDKV
    51
    (2.01)
    TRH201L-SRMDKV
    50.4
    (1.98)
    TRH221L-MBMDKV
    53.9
    (2.12)
    TRH203L-REMDKV
    51.3
    (2.02)
    TRH223L-LEMDKV
    58.4
    (2.30)
    TRH223L-LEMNKV
    59.3
    (2.33)
    KDH200L-SBMDYV
    49.9
    (1.96)
    KDH200L-SRMDYV
    49.4
    (1.94)
    KDH202L-REMDYV
    50.7
    (2.00)
    KDH222L-LEMDYV
    57.4
    (2.26)
    KDH222L-LEMNYV
    58.3
    (2.30)
    (*1):
    Saudi Arabia, Sultanate of Oman, Bahrain, United Arab Emirates, Qatar and Kuwait
    Russia:
    Model
    A
    (mm (in. ) )
    TRH223L-LEMNKX
    50.4
    (1.98)
    Hong Kong:
    Model
    A
    (mm (in. ) )
    TRH201R-SSMDK
    50.5
    (1.99)
    TRH201R-SSPDK
    50.5
    (1.99)
    KDH200R-SSMDY
    49.9
    (1.96)
    KDH200R-SSPDY
    50.2
    (1.98)
    KDH200R-SSPNY
    50.7
    (2.00)
    South and Central America:
    Model
    A
    (mm (in. ) )
    TRH201L-SBMDK
    52
    (2.05)
    TRH203L-REMDK
    51.2
    (2.02)
    TRH203L-RDMDK
    51.3
    (2.02)
    TRH223L-LEMDK
    58.4
    (2.30)
    LH200L-RBMDE
    50.2
    (1.98)
    LH202L-REMDE
    50.7
    (2.00)
    LH202L-RDMDE
    50.8
    (2.00)
    LH222L-LEMDE
    57.7
    (2.27)
    Malaysia:
    Model
    A
    (mm (in. ) )
    KDH200R-RBMDY
    49.4
    (1.94)
    TRH203R-EDMDK
    50.9
    (2.00)
    KDH202R-EDMDY
    50.3
    (1.98)
    Algeria:
    Model
    A
    (mm (in. ) )
    LH200L-RBMDE
    50.2
    (1.98)
    TRH203L-REMDK
    51.3
    (2.02)
    LH202L-REMDE
    50.7
    (2.00)
    Vietnam:
    Model
    A
    (mm (in. ) )
    TRH213L-JDMNK
    54
    (2.13)
    TRH213L-JEMDK
    54.2
    (2.13)
    KDH212L-JEMDY
    53.6
    (2.11)
    Tunisia:
    Model
    A
    (mm (in. ) )
    LH212L-JDMDE
    53.3
    (2.10)
    Others:
    Model
    A
    (mm (in. ) )
    TRH201R-RBMDK
    50.4
    (1.98)
    TRH201L-SBMDK
    52.1
    (2.05)
    TRH221L-MBMDK
    53.9
    (2.12)
    KDH200R-RBMDY
    49.9
    (1.96)
    KDH200R-RBPDY
    50.4
    (1.98)
    KDH200R-SBMDY
    50.4
    (1.98)
    KDH200L-RBMDY
    50.2
    (1.98)
    KDH200L-SBMDY
    50.7
    (2.00)
    LH200R-RBMDE
    49.9
    (1.96)
    LH200R-SBMDE
    50.2
    (1.98)
    LH200L-RBMDE
    50.2
    (1.98)
    TRH203R-REMDK
    50.8
    (2.00)
    TRH203L-REMDK
    51.3
    (2.02)
    TRH203L-RDMDK
    51.4
    (2.02)
    TRH223R-LEMDK
    58.1
    (2.29)
    TRH223L-LEMDK
    58.5
    (2.30)
    TRH223L-LEMNK
    59.5
    (2.34)
    KDH202R-REMDY
    51.3
    (2.02)
    KDH202L-REMDY
    51.3
    (2.02)
    KDH202L-RDMDY
    51.2
    (2.02)
    KDH202L-RDPDY
    51.3
    (2.02)
    KDH222L-LEMDY
    57.9
    (2.28)
    LH202R-REMDE
    50.4
    (1.98)
    LH202L-REMDE
    50.7
    (2.00)
    LH202L-RDMDE
    50.8
    (2.00)
    LH222R-LEMDE
    57.5
    (2.26)
    LH222L-LEMDE
    57.7
    (2.27)



3. INSTALL FENDER APRON MUDGUARD SEAL


    C101965E02
  1. Install the fender apron mudguard seal with the 4 clips.



4. INSTALL FRONT WHEEL

Torque:
100 N*m{ 1,020 kgf*cm , 74 ft.*lbf }



5. STABILIZE SUSPENSION


6. FULLY TIGHTEN TORSION BAR SPRING


    C103219E01
  1. Hold the anchor arm adjust nut and fully tighten the anchor lock nut.

    Torque:
    78 N*m{ 795 kgf*cm , 58 ft.*lbf }



7. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)