FRONT SUSPENSION UPPER ARM > INSTALLATION |
| 1. INSTALL FRONT SUSPENSION UPPER ARM |
![]() |
Install the front suspension upper arm with the 3 bolts.
| 2. INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY |
![]() |
Install the vane pump oil reservoir assembly with the 2 bolts.
| 3. CONNECT FRONT SUSPENSION UPPER ARM |
![]() |
Connect the front suspension upper arm to the steering knuckle with the nut.
Install a new cotter pin.
| 4. CONNECT FRONT SPEED SENSOR |
![]() |
Connect the front speed sensor with the 2 bolts and 2 clips.
| 5. INSTALL FRONT SUSPENSION TORQUE ARM |
![]() |
Install the front suspension torque arm to the suspension upper arm with the 2 bolts.
| 6. TEMPORARILY TIGHTEN TORSION BAR SPRING |
![]() |
Check the right-left identification on the rear ends of the torsion bar springs.
Wrap the splines on both ends of the torsion bar spring with protective tape.
Install the torsion dust cover to the torsion bar spring.
![]() |
Remove the protective tape from the spline on both ends of the torsion bar spring and apply MP grease No.2 to them.
![]() |
Align the matchmarks on the torsion bar spring and torque arm and engage the splines (for anchor arm side).
Align the matchmarks on the torsion bar spring and anchor arm and engage the splines (for torque arm side).
![]() |
Install the following parts to the anchor arm.
Anchor arm swivel. (Part A)
Anchor arm adjusting hexagon bolt. (Part B)
Anchor arm adjusting seat. (Part C)
Anchor arm adjust nut. (Part D)
![]() |
Tighten the anchor arm adjust nut so that the protrusion length of the thread of the anchor arm adjusting hexagon bolt equals the length of dimension A in the table below.
| Model | A (mm (in. ) ) |
| TRH201R-RBMDKQ | 51.4 (2.02) |
| TRH201R-RBPDKQ | 51.4 (2.02) |
| TRH221R-MBMDKQ | 53.9 (2.12) |
| TRH221R-MBPDKQ | 54 (2.12) |
| TRH223R-LEMDKQ | 53.8 (2.12) |
| TRH223R-LEPDKQ | 53.7 (2.11) |
| KDH200R-RBMDYQ | 50.2 (1.98) |
| KDH200R-RBPDYQ | 50.3 (1.98) |
| KDH220R-MBMDYQ | 56.3 (2.22) |
| KDH220R-MBPDYQ | 56.3 (2.22) |
| KDH222R-LEMDYQ | 56.8 (2.24) |
| KDH222R-LEPDYQ | 56.9 (2.24) |
| Model | A |
| TRH201R-RBMDKQ | 51.6 (2.03) |
| TRH221R-MBMDKQ | 53.9 (2.12) |
| TRH223R-LEMDKQ | 54 (2.12) |
| KDH200R-RBMDYQ | 50.5 (1.99) |
| KDH220R-MBMDYQ | 56.4 (2.22) |
| KDH222R-LEMDYQ | 57.2 (2.25) |
| Model | A (mm (in. ) ) |
| TRH223R-LEMDKQ | 52.5 (2.07) |
| KDH222R-LEMDYQ | 55.4 (2.18) |
| KDH222R-LEPDYQ | 55.4 (2.18) |
| TRH201R-SRMDK | 50.4 (1.98) |
| TRH201R-SRPDK | 50.6 (1.99) |
| KDH200R-SRMDY | 49.9 (1.96) |
| KDH200R-SRPDY | 50.4 (1.98) |
| KDH220R-LFMDY | 53.7 (2.11) |
| KDH220R-LFPDY | 53.8 (2.12) |
| Model | A (mm (in. ) ) |
| KDH200R-RBMDY | 49.4 (1.94) |
| TRH213R-KDPNK | 50.7 (2.00) |
| KDH202R-RDMDY | 50.2 (1.98) |
| KDH202R-RDMNY | 47.1 (1.85) |
| KDH222R-LEMDY | 58.4 (2.30) |
| Model | A (mm (in. ) ) |
| KDH200R-RBPDY | 46.9 (1.85) |
| KDH200R-SBMDY | 47 (1.85) |
| KDH202R-REMDY | 47.1 (1.85) |
| Model | A (mm (in. ) ) |
| TRH213L-JDMNK | 53.6 (2.11) |
| TRH223L-LEMNK | 54.1 (2.13) |
| TRH223L-LEPNK | 54.1 (2.13) |
| Model | A (mm (in. ) ) |
| KDH202L-REMDY | 50.5 (1.99) |
| KDH212L-JDMNY | 59.0 (2.32) |
| Model | A (mm (in. ) ) |
| TRH201L-SBMDKV | 51 (2.01) |
| TRH201L-SRMDKV | 50.4 (1.98) |
| TRH221L-MBMDKV | 53.9 (2.12) |
| TRH203L-REMDKV | 51.3 (2.02) |
| TRH223L-LEMDKV | 58.4 (2.30) |
| TRH223L-LEMNKV | 59.3 (2.33) |
| KDH200L-SBMDYV | 49.9 (1.96) |
| KDH200L-SRMDYV | 49.4 (1.94) |
| KDH202L-REMDYV | 50.7 (2.00) |
| KDH222L-LEMDYV | 57.4 (2.26) |
| KDH222L-LEMNYV | 58.3 (2.30) |
| Model | A (mm (in. ) ) |
| TRH223L-LEMNKX | 50.4 (1.98) |
| Model | A (mm (in. ) ) |
| TRH201R-SSMDK | 50.5 (1.99) |
| TRH201R-SSPDK | 50.5 (1.99) |
| KDH200R-SSMDY | 49.9 (1.96) |
| KDH200R-SSPDY | 50.2 (1.98) |
| KDH200R-SSPNY | 50.7 (2.00) |
| Model | A (mm (in. ) ) |
| TRH201L-SBMDK | 52 (2.05) |
| TRH203L-REMDK | 51.2 (2.02) |
| TRH203L-RDMDK | 51.3 (2.02) |
| TRH223L-LEMDK | 58.4 (2.30) |
| LH200L-RBMDE | 50.2 (1.98) |
| LH202L-REMDE | 50.7 (2.00) |
| LH202L-RDMDE | 50.8 (2.00) |
| LH222L-LEMDE | 57.7 (2.27) |
| Model | A (mm (in. ) ) |
| KDH200R-RBMDY | 49.4 (1.94) |
| TRH203R-EDMDK | 50.9 (2.00) |
| KDH202R-EDMDY | 50.3 (1.98) |
| Model | A (mm (in. ) ) |
| LH200L-RBMDE | 50.2 (1.98) |
| TRH203L-REMDK | 51.3 (2.02) |
| LH202L-REMDE | 50.7 (2.00) |
| Model | A (mm (in. ) ) |
| TRH213L-JDMNK | 54 (2.13) |
| TRH213L-JEMDK | 54.2 (2.13) |
| KDH212L-JEMDY | 53.6 (2.11) |
| Model | A (mm (in. ) ) |
| LH212L-JDMDE | 53.3 (2.10) |
| Model | A (mm (in. ) ) |
| TRH201R-RBMDK | 50.4 (1.98) |
| TRH201L-SBMDK | 52.1 (2.05) |
| TRH221L-MBMDK | 53.9 (2.12) |
| KDH200R-RBMDY | 49.9 (1.96) |
| KDH200R-RBPDY | 50.4 (1.98) |
| KDH200R-SBMDY | 50.4 (1.98) |
| KDH200L-RBMDY | 50.2 (1.98) |
| KDH200L-SBMDY | 50.7 (2.00) |
| LH200R-RBMDE | 49.9 (1.96) |
| LH200R-SBMDE | 50.2 (1.98) |
| LH200L-RBMDE | 50.2 (1.98) |
| TRH203R-REMDK | 50.8 (2.00) |
| TRH203L-REMDK | 51.3 (2.02) |
| TRH203L-RDMDK | 51.4 (2.02) |
| TRH223R-LEMDK | 58.1 (2.29) |
| TRH223L-LEMDK | 58.5 (2.30) |
| TRH223L-LEMNK | 59.5 (2.34) |
| KDH202R-REMDY | 51.3 (2.02) |
| KDH202L-REMDY | 51.3 (2.02) |
| KDH202L-RDMDY | 51.2 (2.02) |
| KDH202L-RDPDY | 51.3 (2.02) |
| KDH222L-LEMDY | 57.9 (2.28) |
| LH202R-REMDE | 50.4 (1.98) |
| LH202L-REMDE | 50.7 (2.00) |
| LH202L-RDMDE | 50.8 (2.00) |
| LH222R-LEMDE | 57.5 (2.26) |
| LH222L-LEMDE | 57.7 (2.27) |
| 7. INSTALL FENDER APRON MUDGUARD SEAL |
![]() |
Install the fender apron mudguard seal with the 4 clips.
| 8. INSTALL FRONT WHEEL |
| 9. STABILIZE SUSPENSION |
| 10. FULLY TIGHTEN TORSION BAR SPRING |
![]() |
Hold the anchor arm adjust nut and fully tighten the anchor lock nut.
| 11. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |