Home › BODY ELECTRICAL › AUDIO / VISUAL › RADIO ANTENNA CORD

RADIO ANTENNA CORD > REMOVAL

for Preparation Click here



1. DISCONNECT BATTERY NEGATIVE TERMINAL
(Click here)


2. REMOVE STEERING WHEEL COVER LOWER NO.2


3. REMOVE STEERING WHEEL COVER LOWER NO.3


4. REMOVE HORN BUTTON ASSEMBLY


    C106057E01
  1. Using a "torx" socket wrench (T30), loosen the 2 "torx" screws until the groove along the screw circumference catches on the screw case.

  1. Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand.

  1. Disconnect the horn connector.



    C106058
  1. Disconnect the connector and remove the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



5. REMOVE STEERING WHEEL ASSEMBLY
  1. Remove the steering wheel set nut.

  1. Put matchmarks on the steering wheel assembly and steering main shaft assembly.



    C106843E01
  1. Using SST, remove the steering wheel assembly.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



6. REMOVE STEERING COLUMN COVER LWR


7. REMOVE KEY CYLINDER LIGHT ASSEMBLY


8. REMOVE STEERING COLUMN COVER UPR


9. REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY


    E103535E01
  1. Disconnect the connector.

  1. Disengage the claw and remove the headlight dimmer switch as shown in the illustration.

    NOTICE:
    If the claw is pushed with excessive force, it may be broken.

    HINT:
    Slide the steering column upper cover upward to remove the headlight dimmer switch.



10. REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY


    E103129E01
  1. Disconnect the connector.

  1. Disengage the claw and remove the wiper switch as shown in the illustration.

    NOTICE:
    If the claw is pushed with excessive force, it may be broken.

    HINT:
    Slide the steering column cover upper upward to remove the wiper switch.



11. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH NO.2


    B102813
  1. Using a moulding remover, disengage the 3 claws and remove the instrument cluster finish panel No.2 garnish.



12. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY CENTER


  1. Using a roof moulding remover, disengage the claws in the order shown in the illustration.


    B102814E01



    B102815E01
  1. Attach tape to the positions shown in the illustration in order to prevent the instrument cluster finish panel sub-assembly center from being damaged.

  1. Using a moulding remover, disengage the claw.



    B102816
  1. Hold the panel as shown in the illustration and pull it toward the rear of the vehicle to disengage the claws.



    B102817
  1. While supporting the panel with your right hand, pull it toward the rear of the vehicle to disengage the claws.



    B102818
  1. Hold the panel as shown in the illustration and disengage the claws.



    B102819
  1. Hold the panel as shown in the illustration and pull it toward the rear of the vehicle to disengage the claws. Remove the instrument cluster finish panel sub-assembly center.



13. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH NO.1


    B102820
  1. Using a moulding remover, disengage the 3 claws and remove the instrument cluster finish panel No.1 garnish.



14. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    B102821
  1. Using a moulding remover, disengage the 4 claws and remove the instrument cluster finish panel assembly.



15. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B102822
  1. Disengage the 6 claws and remove the instrument cluster finish panel sub-assembly.



16. REMOVE COMBINATION METER ASSEMBLY


    B102823
  1. Remove the 2 screws.



    B102824E01
  1. Disengage the 2 claws.

  1. Disconnect the connector and remove the combination meter assembly.



17. REMOVE INSTRUMENT PANEL CUP HOLDER ASSEMBLY


18. REMOVE STEREO OPENING COVER


    B102826
  1. Remove the 4 screws <C> and the stereo opening cover with bracket.



19. REMOVE RADIO RECEIVER ASSEMBLY


    E103058
  1. Remove the 4 screws.

  1. Disconnect the connectors and the radio receiver assembly with bracket.



20. REMOVE INSTRUMENT PANEL FINISH PANEL LOWER


    B102827E01
  1. Using a clip remover, remove the 2 clips (A).

  1. Disengage the 4 clips (B).

  1. Disconnect the connector.



    B102838
  1. Push the positions indicated by the arrows in the illustration to separate the fuel lid lock control cable and bonnet (hood) control cable assembly from the panel.
    Remove the instrument panel finish lower.



21. REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY NO.1


    B102828
  1. Using a clip remover, remove the 2 clips

  1. Disengage the 3 claws and remove the instrument panel No.1 under cover sub-assembly.



22. REMOVE PARKING BRAKE HOLE COVER


    B102829E01
  1. Disengage the 6 claws and remove the parking brake hole cover.



23. REMOVE SHIFT LEVER KNOB


    B102830E01
  1. Turn the shift lever knob in the direction indicated by the arrow and remove it.



24. REMOVE SHIFTING HOLE COVER ASSEMBLY


    B102831E01
  1. Manual Transmission:
    Disengage the 6 claws and remove the shifting hole cover assembly.

  1. Automatic Transmission:
    Disengage the 8 claws and remove the shifting hole cover assembly.



25. REMOVE INSTRUMENT PANEL FINISH PANEL LOWER CENTER


    B102832E01
  1. Disengage the 8 claws and remove the instrument panel finish panel lower center.



26. REMOVE FLOOR SHIFT SHIFT LEVER ASSEMBLY
For 5L-E
For 2KD-FTV, 2TR-FE


27. REMOVE SHIFT LOCK CONTROL UNIT ASSEMBLY
For 2KD-FTV
For 2TR-FE


28. REMOVE AIR CONDITIONER PANEL SUB-ASSEMBLY


    E108769E01
  1. Release the 9 clips and the air conditioner panel sub-assembly.

  1. Disconnect the connector and remove the air conditioner panel sub-assembly.



    E108770E01
  1. Release clamp.

  1. Disengage the 2 claws and then remove the boost ventilator control cable sub-assembly.



    E108771E01
  1. Disengage the 2 claws and then remove the defroster damper control cable sub-assembly.



    E108139
  1. Remove the 2 screws and remove the heater control hose.



29. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    B102833E01
  1. Push the positions indicated by the arrows in the illustration inward to release the 2 stoppers.



    B102834E01
  1. Pull the glove compartment door assembly in the direction indicated by the arrow shown in the illustration and disengage the 2 hinges.

  1. Remove the glove compartment door assembly.



30. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY
  1. Separate the clamp from the reinforcement.



    C106065E01
  1. Disconnect the airbag connector.



    C106066
  1. Remove the 2 bolts from the reinforcement.



    C106067
  1. Separate the clip and clamp, and remove the instrument panel passenger airbag assembly.



31. REMOVE HAZARD WARNING SIGNAL SWITCH ASSEMBLY


32. REMOVE ASSIST GRIP PLUG


    B113343
  1. Using a screwdriver, disengage the assist grip plug No.1.

    HINT:
    1. Tape the screwdriver tip before use.
    2. Use the same procedures described for the RH side.



33. REMOVE ASSIST GRIP ASSEMBLY


    B113344
  1. Remove the 2 screws and assist grip.

    HINT:
    Use the same procedures described for the RH side.



34. REMOVE FRONT PILLAR GARNISH LH
w/o Rear Cooler
w/ Rear Cooler


35. REMOVE FRONT PILLAR GARNISH RH


36. REMOVE INSTRUMENT PANEL ASSEMBLY
  1. Remove the 4 bolts <A> and 3 screws <B>.

  1. Remove the 2 nuts <D> and 2 clips.

  1. Disengage the clamps.

  1. Disengage the DLC3 connector from the wire harness clamp bracket.

  1. Disconnect the instrument panel wire No.2 connector. (passenger side)



  1. Pull the instrument panel sub-assembly towards you and check that no wire harnesses are stuck in the body.

    NOTICE:
    Do not damage the instrument panel assembly with the steering column etc. when taking it out of the vehicle.



    B102835E01

  1. Disconnect the instrument panel wire No.2 connector. (driver side)



37. REMOVE RADIO ANTENNA CORD


    E110957E01
  1. Disconnect the connector.

  1. Remove the 4 clamps and the radio antenna cord.