Home › BODY › WINDSHIELD / WINDOWGLASS › WINDSHIELD GLASS

WINDSHIELD GLASS > INSTALLATION

for Preparation Click here



1. CLEAN WINDSHIELD GLASS


    B073128
  1. Using a scraper, remove the stoppers, dams and adhesive sticking to the windshield glass.

  1. Clean the outer edges of the windshield glass with white gasoline.

    NOTICE:
    1. Do not touch the windshield glass surface after cleaning it.
    2. Even if using new windshield glass, clean the windshield glass with white gasoline.



2. CLEAN VEHICLE BODY


    B073084E02
  1. Clean and shape the contact surface of the vehicle body.

    1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

      NOTICE:
      Be careful not to damage the vehicle body.

    2. Clean the contact surface of the vehicle body with cleaner.

      HINT:
      Even if all the adhesive has been removed, clean the vehicle body.



3. INSTALL WINDSHIELD GLASS STOPPER
  1. Apply Primer G to the installation part of the spacers.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.



  1. Install 2 new spacers onto the windshield glass, as shown in the illustration.


    B101847E01

    Specification:
    Area
    Measurement
    a
    20.0 mm (0.787 in.)
    b
    9.0 mm (0.354 in.)
    c
    10.0 mm (0.393 in.)



4. INSTALL WINDSHIELD GLASS ADHESIVE DAM
  1. Apply Primer G to the installation part of the windshield glass adhesive dams.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.



  1. Install new windshield glass adhesive dams all the way around the windshield glass except where the spacers are installed, as shown in the illustration.


    B101848E02

    Specification:
    Area
    Measurement
    a
    7.0 mm (0.276 in.)
    b
    23.2 mm (0.913 in.)



5. INSTALL WINDSHIELD GLASS


    B115414E01
  1. Position the windshield glass.

    1. Using a suction cup, place the windshield glass in the correct position.

    2. Check that the whole contact surface of the windshield glass rim is perfectly even.

    3. Place matchmarks over the windshield glass and vehicle body on the locations indicated in the illustration.

      HINT:
      1. Placing matchmarks is only necessary if the windshield glass being installed is new. If it is reused windshield glass, matchmarks should already be present.
      2. When reusing the windshield glass, check and correct the matchmark positions.

      NOTICE:
      Check that the spacers are attached to the vehicle body correctly.

    4. Using a suction cup, remove the windshield glass.



    B083465E01
  1. Using a brush, apply Primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the Primer M to dry for 3 minutes or more.
    2. Do not apply Primer M to the adhesive.
    3. Throw away any leftover Primer M.
    4. Do not apply too much Primer M.



  1. Using a brush or sponge, apply Primer G to the contact surface of the windshield glass.


    B114784E01

    HINT:
    If Primer G is applied to an area other than that which is specified, wipe off the primer with white gasoline before it dries.

    NOTICE:
    1. Allow the Primer G to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.



  1. Apply adhesive.

    Adhesive:
    Part No. 08850-00801 or equivalent




      B115241E01
    1. Cut off the tip of the cartridge nozzle, as shown in the illustration.

      Specification:
      Area
      Measurement
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)

      HINT:
      After cutting off the tip, use all adhesive within the time described in the table below.

      Usage timeframe:
      Temperature
      Usage Timeframe
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.



    3. Apply adhesive to the windshield glass as shown as shown in the illustration.


      B101852E01

      Specification:
      Area
      Measurement
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)



    B073132E01
  1. Install the windshield glass to the vehicle body.

    1. Using a suction cup, position the windshield glass so that the matchmarks are aligned. Press it in gently along the rim.

    2. Lightly press the front surface of the windshield glass to ensure that the windshield glass is securely fit to the vehicle body.

      NOTICE:
      1. Allow the primer to dry for 3 minutes or more.
      2. Check that the spacers are attached to the vehicle body correctly.
      3. Check that the vehicle body and windshield glass have a small gap between them.

    3. Hold the windshield glass in place securely with protective tape or equivalent until the adhesive hardens.



6. INSTALL WINDSHIELD MOULDING OUTER UPPER


    B101849E01
  1. Using a brush or sponge, apply Primer G to the contact surface of the windshield glass.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Install new windshield moulding outer upper, as shown in the illustration.

    NOTICE:
    Do not drive the vehicle for the amount of time described in the table below.

    Minimum time:
    Temperature
    Minimum time prior to driving vehicle
    35°C (95°F)
    1 hour 30 minutes
    20°C (68°F)
    5 hours
    5°C (41°F)
    24 hours



7. CHECK FOR LEAKS AND REPAIR
  1. Conduct a leak test after the adhesive has completely hardened.



8. INSTALL WINDSHIELD WIPER MOTOR AND LINK


    E108766
  1. Engage the grommet as shown in the illustration.

  1. Install the windshield wiper motor and link assembly with the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Connect the connector.



9. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSY


    E108767E01
  1. Body type narrow:

    1. Install the cowl top ventilator louver sub-assembly with the 10 claws and 6 clips.

  1. Body type wide:

    1. Install the cowl top ventilator louver sub-assembly with the 11 claws and 7clips.

  1. Connect the washer hose.



10. INSTALL COWL VENT COVER LH


11. INSTALL COWL VENT COVER RH


12. INSTALL FR WIPER ARM LH


    B108016E03
  1. Operate the wiper, and stop the windshield wiper motor assembly at the automatic stop position.

  1. Clean the wiper arm serrations.

  1. Clean the wiper pivot serrations with a wire brush (when reinstalling).



    E108758E01
  1. Install the front wiper arm and blade assembly LH with the nut at the position as shown in the illustration.

    Torque:
    25 N*m{ 225 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the arm hinge by hand to fasten the nut.



13. INSTALL FR WIPER ARM RH


    B108016E03
  1. Clean the wiper arm serrations.

  1. Clean the wiper pivot serrations with a wire brush (when reinstalling).



    E108757E01
  1. Install the front wiper arm and blade assembly RH with the nut at the position as shown in the illustration.

    Torque:
    25 N*m{ 225 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the arm hinge by hand to fasten the nut.



14. INSTALL WINDSHIELD WIPER ARM COVER
  1. Install the 2 windshield wiper arm covers.

  1. Operate the front wipers while spraying water or washer fluid on the windshield. Make sure that the wipers function properly and there is no interference with the vehicle body.



15. INSTALL INNER REAR VIEW MIRROR ASSY


16. INSTALL ROOF NO.1 HEADLINING


17. INSTALL ROOM LAMP ASSEMBLY NO.1


18. INSTALL RH VISOR ASSEMBLY


19. INSTALL LH VISOR ASSEMBLY


20. INSTALL VISOR HOLDER


21. INSTALL ASSIST GRIP ASSEMBLY REAR


22. INSTALL FRONT PILLAR GARNISH LH


23. INSTALL FRONT PILLAR GARNISH RH


24. INSTALL ASSIST GRIP


25. INSTALL FRONT ASSIST GRIP PLUG