Home › BODY › WINDSHIELD / WINDOWGLASS › WINDSHIELD GLASS

WINDSHIELD GLASS > REMOVAL

for Preparation Click here



1. REMOVE FRONT ASSIST GRIP PLUG


    B113343
  1. Using a screwdriver, disengage the assist grip plug No.1.

    HINT:
    1. Tape the screwdriver tip before use.
    2. Use the same procedures described for the RH side.



2. REMOVE ASSIST GRIP


    B113344
  1. Remove the 2 screws and assist grip.

    HINT:
    Use the same procedures described for the RH side.



3. REMOVE FRONT PILLAR GARNISH LH
w/o Rear Cooler
w/ Rear Cooler


4. REMOVE FRONT PILLAR GARNISH RH


5. REMOVE ASSIST GRIP ASSEMBLY REAR


    B113269
  1. Remove the 2 screws and assist grip assembly rear.



6. REMOVE VISOR HOLDER


    B103025
  1. Remove the screw.

  1. Using a moulding remover, disengage the claw and remove the visor holder.

    HINT:
    Use the same procedures described for the RH side.



7. REMOVE LH VISOR ASSEMBLY


    B113346
  1. Remove the 2 screws and visor assembly LH.



8. REMOVE RH VISOR ASSEMBLY

HINT:
Use the same procedures described for the LH side.



9. REMOVE ROOM LAMP ASSEMBLY NO.1


    B070797
  1. Using a screwdriver, disengage the 4 claws and remove the room light lens cover.

    HINT:
    Tape the screwdriver tip before use.



    B103034
  1. Remove the 2 screws.

  1. Disconnect the connector and remove the room light assembly No.1.



10. REMOVE ROOF NO.1 HEADLINING


    B112985E02
  1. w/ Rear Cooler:
    Remove the 4 screws.

  1. Using a clip remover, disengage the 15 clips and remove the roof headlining No.1.

    HINT:
    The clips in the illustration are part of the components. Remove them together with the roof headlining No.1.



11. REMOVE INNER REAR VIEW MIRROR ASSEMBLY


    B101366E01
  1. Disengage the 2 claws and separate the inner rear view mirror assembly cover as shown in the illustration.



    B101367E01
  1. Remove the inner rear view mirror assembly as shown in the illustration.



12. REMOVE WINDSHIELD WIPER ARM COVER
  1. Remove the 2 windshield wiper arm covers.



13. REMOVE FR WIPER ARM RH
  1. Remove the nut and front wiper arm and blade assembly RH.



14. REMOVE FR WIPER ARM LH
  1. Remove the nut and front wiper arm and blade assembly LH.



15. REMOVE COWL VENT COVER RH


    E108759
  1. Disengage the 2 claws and remove the cowl vent cover RH as shown in the illustration.



16. REMOVE COWL VENT COVER LH


    E108760
  1. Disengage the 2 claws and remove the cowl vent cover LH as shown in the illustration.



17. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSY


    E108761E01
  1. Disconnect the washer hose at position <a> shown in the illustration.

  1. Body type narrow:

    1. Disengage the 10 claws, and remove the 6 clips and cowl top ventilator louver sub-assembly.

  1. Body type wide:

    1. Disengage the 11 claws, and remove the 7 clips and cowl top ventilator louver sub-assembly.



18. REMOVE WINDSHIELD WIPER MOTOR AND LINK


    E108762E01
  1. Disconnect the connector.

  1. Remove the 2 bolts.

  1. Disengage the grommet and remove the windshield wiper motor and link assembly as shown in the illustration.



19. REMOVE WINDSHIELD MOULDING OUTER UPPER


    B050448E03
  1. Using a knife, cut off the moulding as shown in the illustration.

    NOTICE:
    Be careful not to damage the vehicle body with the knife.

  1. Remove the remaining moulding.

    HINT:
    Make a partial cut in the moulding. Then pull and remove it by hand.



20. REMOVE WINDSHIELD GLASS


    B115412E01
  1. Apply protective tape to the outer surface of the vehicle body to prevent scratches.

  1. From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.

  1. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

    NOTICE:
    1. When separating the glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.
    2. To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.



    B115413E01
  1. Place matchmarks over the windshield glass and vehicle body on the locations indicated in the illustration.

    HINT:
    Matchmarks do not need to be placed if the windshield glass is not going to be reused.

  1. Cut through the adhesive by pulling the piano wire around the windshield glass.

  1. Disengaged the spacers.

  1. Using a suction cup, remove the windshield glass.

    NOTICE:
    Leave as much adhesive on the vehicle body as possible when removing the windshield glass.