Home › BODY › WINDSHIELD / WINDOWGLASS › FRONT SIDE WINDOW GLASS

FRONT SIDE WINDOW GLASS > INSTALLATION

for Preparation Click here



1. CLEAN FRONT SIDE WINDOW GLASS


    B073128
  1. Using a scraper, remove the spacers, moulding and adhesive from the back door glass.

  1. Clean the outer edge of the back door glass with white gasoline.

    NOTICE:
    1. Do not touch the back door glass surface after cleaning it.
    2. Even if using new back door glass, clean the back door glass with white gasoline.



2. CLEAN VEHICLE BODY


    B073084
  1. Clean and shape the contact surface of the vehicle body.

    1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

      NOTICE:
      Be careful not to damage the vehicle body.



3. INSTALL FRONT SIDE WINDOW GLASS STOPPER


    B102386E01
  1. Apply Primer G to the glass where the spacers will be installed.

    HINT:
    If primer G is applied to an area other than that which is specified, wipe off the primer with white gasoline before it dries.

    NOTICE:
    1. Allow the Primer G to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Install 2 new spacers onto the back door glass as shown in the illustration.



4. INSTALL FRONT SIDE WINDOW GLASS


    B114789E01
  1. Using a brush, apply Primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the Primer M to dry for 3 minutes or more.
    2. Do not apply Primer M to the adhesive.
    3. Throw away any leftover Primer M.
    4. Do not apply too much Primer M.



  1. Using a brush or sponge, apply Primer G to the contact surface of the glass.


    B114785E01

    HINT:
    If Primer G is applied to an area other than that which is specified, wipe off the primer with white gasoline before it dries.

    NOTICE:
    1. Allow the Primer G to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.



  1. Apply adhesive to the glass.

    Adhesive:
    Part No. 08850-00801 or equivalent




      B115241E01
    1. Cut off the tip of cartridge nozzle as shown in the illustration.

      Specification:
      Area
      Measurement
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)

      HINT:
      After cutting off the tip, use all adhesive within the time written in the table below.

      Usage timeframe 
      Temperature
      Usage Timeframe
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.



    3. Apply adhesive to the back door glass as shown in the illustration.


      B115249E02

      Specification 
      Area
      Measurement
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)
      c
      25.1 mm (0.988 in.)
      d
      14.1 mm (0.555 in.)
      e
      11.5 mm (0.452 in.)

  1. Install the back door glass to the vehicle body.

    1. Lightly press the front surface of the back door glass to ensure that the back door glass is securely fit to the vehicle body.

      NOTICE:
      1. Check that the spacers are attached to the vehicle body correctly.
      2. Check that the spacers are attached to the vehicle body correctly.

    2. Hold the back door glass in place securely with protective tape or equivalent until the adhesive hardens.

      NOTICE:
      Do not drive the vehicle for the amount of time written in the table below.

      Minimum time 
      Temperature
      Minimum time prior to driving vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours



5. CHECK FOR LEAKS AND REPAIR
  1. Conduct a leak test after the adhesive has completely hardened.



6. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    B101171E01
  1. Engage the clips and claw, and install the rear door trim board sub-assembly.



    B101169
  1. Using a "torx" socket wrench, install the 2 "torx" screws.



7. INSTALL SLIDE DOOR WINDOW GARNISH LH


    B101167E01
  1. Engage the clips and install the slide door window garnish.