Home › BODY › WINDSHIELD / WINDOWGLASS › REAR QUARTER WINDOW GLASS

REAR QUARTER WINDOW GLASS > INSTALLATION

for Preparation Click here



1. CLEAN QUARTER WINDOW GLASS


    B073128
  1. Using a scraper, remove the stoppers, moulding and adhesive from the rear quarter window glass.

  1. Clean the outer edge of the rear quarter window glass with white gasoline.

    NOTICE:
    1. Do not touch the surface after cleaning it.
    2. Even if using new rear quarter window glass, clean the rear quarter window glass with white gasoline.



2. CLEAN VEHICLE BODY


    B073084
  1. Clean and shape the contact surface of the vehicle body.

    1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

      NOTICE:
      Be careful not to damage the vehicle body.

    2. Clean the contact surface of the vehicle body with cleaner.

      HINT:
      Even if all the adhesive has been removed, clean the vehicle body.



3. INSTALL REAR QUARTER WINDOW GLASS STOPPER


    B102387E01
  1. Apply Primer G to the glass where the stoppers will be installed.

    HINT:
    If primer G is applied to an area other than that which is specified, wipe off the primer with white gasoline before it dries.

    NOTICE:
    1. Allow the Primer G to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Install 2 new stoppers onto the rear quarter window glass as shown in the illustration.



4. INSTALL REAR QUARTER WINDOW GLASS


    B114789E01
  1. Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the Primer M to dry for 3 minutes or more.
    2. Do not apply Primer M to the adhesive.
    3. Throw away any leftover Primer M.
    4. Do not apply too much Primer M.



  1. Using a brush or sponge, apply Primer G to the contact surface of the rear quarter window glass.


    B114788E01

    HINT:
    If Primer G is applied to an area other than that which is specified, wipe off the primer with white gasoline before it dries.

    NOTICE:
    1. Allow the Primer G to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.



  1. Apply adhesive to the rear quarter window glass.

    Adhesive:
    Part No. 08850-00801 or equivalent




      B115241E01
    1. Cut off the tip of cartridge nozzle as shown in the illustration.

      Specification:
      Area
      Measurement
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)

      HINT:
      After cutting off the tip, use all adhesive within the time written in the table below.

      Usage timeframe 
      Temperature
      Usage Timeframe
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.



    3. Apply adhesive to the back door glass as shown in the illustration.


      B115254E01

      Specification 
      Area
      Measurement
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)
      c
      11.5 mm (0.452 in.)
      d
      14.6 mm (0.574 in.)

  1. Install the rear quarter window glass to the vehicle body.

    1. Lightly press the front surface of the back door glass to ensure that the rear quarter window glass is securely fit to the vehicle body.

      NOTICE:
      1. Check that the spacers are attached to the vehicle body correctly.
      2. Check that the vehicle body and rear quarter window glass have a small gap between them.

    2. Hold the rear quarter window glass in place securely with protective tape or equivalent until the adhesive hardens.

      NOTICE:
      Do not drive the vehicle for the amount of time written in the table below.

      Minimum time 
      Temperature
      Minimum time prior to driving vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours



5. CHECK FOR LEAKS AND REPAIR
  1. Conduct a leak test after the adhesive has completely hardened.



6. INSTALL ROOF SIDE GARNISH INNER UPPER LH


7. INSTALL QUARTER PILLAR GARNISH LH


8. INSTALL QUARTER TRIM PANEL ASSEMBLY REAR LH


9. INSTALL BACK DOOR WEATHERSTRIP


10. INSTALL BACK DOOR SCUFF PLATE


11. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH


    B103246
  1. Install the front seat outer belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B115749
  1. Engage the 2 claws to install the cover.



    B103256
  1. Install the front seat outer belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }