Home › BODY › WINDSHIELD / WINDOWGLASS › BACK DOOR GLASS

BACK DOOR GLASS > INSTALLATION

for Preparation Click here



1. CLEAN BACK DOOR GLASS


    B073128
  1. Using a scraper, remove the spacers, moulding and adhesive from the back door glass.

  1. Clean the outer edge of the back door glass with white gasoline.

    NOTICE:
    1. Do not touch the back door glass surface after cleaning it.
    2. Even if using new back door glass, clean the back door glass with white gasoline.



2. CLEAN VEHICLE BODY


    B073084
  1. Clean and shape the contact surface of the vehicle body.

    1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

      NOTICE:
      Be careful not to damage the vehicle body.

    2. Clean the contact surface of the vehicle body with cleaner.

      HINT:
      Even if all the adhesive has been removed, clean the vehicle body.



3. INSTALL BACK WINDOW GLASS CLIP LH


    B102894E01
  1. Apply Primer G to the glass where the clip will be installed.

    HINT:
    If primer G is applied to an area other than that which is specified, wipe off the primer with white gasoline before it dries.

    NOTICE:
    1. Allow the Primer G to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Install a new clip onto the back door glass as shown in the illustration.



4. INSTALL BACK WINDOW GLASS CLIP RH


    B102894E02
  1. Apply Primer G to the glass where the clip will be installed.

    HINT:
    If primer G is applied to an area other than that which is specified, wipe off the primer with white gasoline before it dries.

    NOTICE:
    1. Allow the Primer G to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Install a new clip onto the back door glass as shown in the illustration.



5. INSTALL BACK DOOR GLASS SPACER NO.1


    B102894E03
  1. Apply Primer G to the glass where the spacers will be installed.

    HINT:
    If primer G is applied to an area other than that which is specified, wipe off the primer with white gasoline before it dries.

    NOTICE:
    1. Allow the Primer G to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Install 2 new spacers onto the back door glass as shown in the illustration.



6. INSTALL BACK WINDOW GLASS SPACER NO.2


    B102894E04
  1. Apply Primer G to the glass where the spacers will be installed.

    HINT:
    If primer G is applied to an area other than that which is specified, wipe off the primer with white gasoline before it dries.

    NOTICE:
    1. Allow the Primer G to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Install 2 new spacers onto the back door glass as shown in the illustration.



7. INSTALL BACK DOOR GLASS


    B114789E01
  1. Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.

    NOTICE:

    1. B101853E01
      Allow the Primer M to dry for 3 minutes or more.
    2. Do not apply Primer M to the adhesive.
    3. Throw away any leftover Primer M.
    4. Do not apply too much Primer M.



  1. Using a brush or sponge, apply Primer G to the contact surface of the back door glass.


    B114787E03

    HINT:
    If Primer G is applied to an area other than that which is specified, wipe off the primer with white gasoline before it dries.

    NOTICE:
    1. Allow the Primer G to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Apply adhesive to the back door glass.

    Adhesive:
    Part No. 08850-00801 or equivalent



    B115241E01
  1. Cut off the tip of cartridge nozzle as shown in the illustration.

    Specification:
    Area
    Measurement
    a
    12.0 mm (0.472 in.)
    b
    8.0 mm (0.315 in.)

    HINT:
    After cutting off the tip, use all adhesive within the time written in the table below.

    Usage timeframe 
    Temperature
    Usage Timeframe
    35°C (95°F)
    15 minutes
    20°C (68°F)
    1 hour 40 minutes
    5°C (41°F)
    8 hours

  1. Load the sealer gun with the cartridge.



  1. Apply adhesive to the back door glass as shown in the illustration.


    B115252E01

    Specification 
    Area
    Measurement
    a
    12.0 mm (0.472 in.)
    b
    8.0 mm (0.315 in.)
    c
    13.0 mm (0.511 in.)

  1. Install the back door glass to the vehicle body.

    1. Lightly press the front surface of the back door glass to ensure that the back door glass is securely fit to the vehicle body.

      NOTICE:
      1. Check that the spacers are attached to the vehicle body correctly.
      2. Check that the vehicle body and back door glass have a small gap between them.

    2. Hold the back door glass in place securely with protective tape or equivalent until the adhesive hardens.

      NOTICE:
      Do not drive the vehicle for the amount of time written in the table below.

      Minimum time 
      Temperature
      Minimum time prior to driving vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours



8. CHECK FOR LEAKS AND REPAIR
  1. Conduct a leak test after the adhesive has completely hardened.

  1. Seal any leaks with auto glass sealer.



9. INSTALL REAR WIPER MOTOR ASSEMBLY


    E104706E01
  1. Install the grommet as shown in the illustration.



    E103138E01
  1. Install the rear wiper motor with the 3 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Install the clamp and connect the connector.



10. INSTALL BACK DOOR TRIM BOARD ASSEMBLY UPPER


    B101147E01
  1. Engage the clips and install the back door trim board assembly upper.



11. INSTALL REAR WIPER LINK PIVOT WASHER NO.1


    E103141E02
  1. Install the rear No.1 wiper link pivot washer from the outside of the vehicle with the installation mark at the top.



    E103140
  1. Using the socket wrench (27 mm), install the lock nut.

    Torque:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Do not damage the glass.



12. INSTALL REAR WIPER SHAFT COVER


13. INSTALL REAR WIPER ARM


    B108016E03
  1. Operate the wiper, and stop the rear wiper motor at the automatic stop position.

  1. Clean the wiper arm serrations.

  1. Clean the wiper pivot serrations with a wire brush (when reinstalling).



    E103534E01
  1. Install the rear wiper arm and blade assembly with the nut at the position as shown in the illustration.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

    HINT:
    Hold the arm hinge by hand to fasten the nut.

  1. Operate the rear wiper while spraying water or washer fluid on the windshield. Make sure that the wipers function properly and there is no interference with the vehicle body.