Home › BODY ELECTRICAL › WIPER AND WASHER › WIPER SWITCH

WIPER SWITCH > INSPECTION

for Preparation Click here



1. INSPECT WIPER SWITCH (LHD)


    B113740
  1. Continuity Check

    1. Measure the resistance according to the value(s) in the table below.

      Resistance:
      Front Wiper Switch:
      Switch position
      Tester connection
      Specified condition
      MIST
      17 (+B) - 7 (+1)
      Below 1 Ω
      OFF
      16 (+S) - 7 (+1)
      Below 1 Ω
      INT
      16 (+S) - 7 (+1)
      Below 1 Ω
      LO
      17 (+B) - 7 (+1)
      Below 1 Ω
      HI
      17 (+B) - 8 (+2)
      Below 1 Ω
      Front Washer Switch:
      Switch position
      Tester connection
      Specified condition
      OFF
      2 (E) - 11 (WF)
      10 kΩ or higher
      ON
      2 (E) - 11 (WF)
      Below 1 Ω
      Rear Wiper and Washer Switch:
      Switch position
      Tester connection
      Specified condition
      WASH
      2 (E) - 12 (WR)
      Below 1 Ω
      OFF
      2 (E) - 13 (C1R)
      2 (E) - 12 (WR)
      2 (E) - 10 (+1R)
      10 kΩ or higher
      INT
      2 (E) - 13 (C1R)
      Below 1 Ω
      ON
      2 (E) - 10 (+1R)
      Below 1 Ω
      ON + WASH
      2 (E) - 12 (WR)
      2 (E) - 10 (+1R)
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.



  1. Intermittent Operation Check

    1. Connect the voltmeter (+) terminal to terminal 7 (+1) and the voltmeter (-) terminal to terminal 2 (E).

    2. Connect the battery's positive (+) lead to terminal 17 (+B), and connect the battery's negative (-) lead to terminals 2 (E) and 16 (+S).

    3. Turn the wiper switch to the INT position.

    4. Connect the battery's positive (+) lead to terminal 16 (+S) for 5 seconds.



    5. Connect the battery's negative (-) lead to terminal 16 (+S) to operate the intermittent wiper relay. Measure the voltage between terminals 7 (+1) and 2 (E).

      OK:
      Refer to the illustration below.



      B113741E01

      If the result is not as specified, replace the wiper switch.



    B113742E01
  1. Front Washer Operation Check

    1. Turn the wiper switch to the OFF position.

    2. Connect the battery's positive (+) lead to terminal 17 (+B), connect the battery's negative (-) to terminals 16 (+S) and 2 (E).

    3. Connect the voltmeter (+) terminal to terminal 7 (+1) and the voltmeter (-) terminal to terminal 2 (E). Measure the voltage between terminals 7 (+1) and 2 (E) when turning the washer switch ON and OFF respectively.

      OK:
      Refer to the illustration.

      If the result is not as specified, replace the wiper switch.



2. INSPECT WIPER SWITCH (RHD)


    B113740
  1. Continuity Check

    1. Measure the resistance according to the value(s) in the table below.

      Resistance:
      Front Wiper Switch:
      Switch position
      Tester connection
      Specified condition
      MIST
      11 (+B) - 3 (+1)
      Below 1 Ω
      OFF
      12 (+S) - 3 (+1)
      Below 1 Ω
      INT
      12 (+S) - 3 (+1)
      Below 1 Ω
      LO
      11 (+B) - 3 (+1)
      Below 1 Ω
      HI
      11 (+B) - 2 (+2)
      Below 1 Ω
      Front Washer Switch:
      Switch position
      Tester connection
      Specified condition
      OFF
      8 (E) - 17 (WF)
      10 kΩ or higher
      ON
      8 (E) - 17 (WF)
      Below 1 Ω
      Rear Wiper and Washer Switch:
      Switch position
      Tester connection
      Specified condition
      Washer
      8 (E) - 16 (WR)
      Below 1 Ω
      OFF
      8 (E) - 15 (C1R)
      8 (E) - 16 (WR)
      8 (E) - 18 (+1R)
      10 kΩ or higher
      INT
      8 (E) - 15 (C1R)
      Below 1 Ω
      ON
      8 (E) - 18 (+1R)
      Below 1 Ω
      On + Washer
      8 (E) - 16 (WR)
      8 (E) - 18 (+1R)
      Below 1 Ω

      If result is not as specified, replace the wiper switch.



  1. Intermittent Operation Check

    1. Connect the voltmeter (+) terminal to terminal 3 (+1) and the voltmeter (-) terminal to terminal 8 (E).

    2. Connect the battery's positive (+) lead to terminal 11 (+B), and connect the battery's negative (-) lead to terminals 8 (E) and 12 (+S).

    3. Turn the wiper switch to the INT position.

    4. Connect the battery's positive (+) lead to terminal 12 (+S) for 5 seconds.



    5. Connect the battery's negative (-) lead to terminal 12 (+S) to operate the intermittent wiper relay. Measure the voltage between terminals 3 (+1) and 8 (E).

      OK:
      Refer to the illustration below.



      B113741E02

      If the result is not as specified, replace the wiper switch.



    B113742E02
  1. Front Washer Operation Check

    1. Turn the wiper switch to the OFF position.

    2. Connect the battery's positive (+) lead to terminal 11 (+B), and connect the battery's negative (-) to terminals 12 (+S) and 8 (E).

    3. Connect the voltmeter (+) terminal to terminal 3 (+) and the voltmeter (-) terminal to terminal 8 (E). Measure the voltage between terminals 3 (+1) and 8 (E) when turning the washer switch ON and OFF respectively.

      OK:
      Refer to the illustration.

      If the result is not as specified, replace the wiper switch.