Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM (w/ Secondary Air Injection System)

SFI SYSTEM (w/ Secondary Air Injection System) > TERMINALS OF ECM

for Preparation Click here



A066714E06

HINT:
The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the STD Voltages column. The illustration above can be used as a reference to identify the ECM terminal locations.


Symbols (Terminal No.)
Wiring Colors
Terminal Descriptions
Conditions
STD Voltages
BATT (B9-3) - E1 (D1-3)
B-R - BR
Battery (for measuring the battery voltage and for the ECM memory)
Always
9 to 14 V
+BM (B9-7) - E1 (D1-3)
Y-B - BR
Power source of throttle motor
Always
9 to 14 V
IGSW (B9-9) - E1 (D1-3)
B-R - BR
Ignition switch
Ignition switch to the ON position
9 to 14 V
+B (B9-1) - E1 (D1-3)
B-R - BR
Power source of ECM
Ignition switch to the ON position
9 to 14 V
MREL (B9-8) - E1 (D1-3)
G-Y - BR
EFI relay
Ignition switch to the ON position
9 to 14 V
VC (D1-18) - E2 (D1-28)
LB - Y-R
Power source of sensor
(specific voltage)
Ignition switch to the ON position
4.5 to 5.0 V
VTA1 (D1-20) - E2 (D1-28)
R - Y-R
Throttle position sensor
(for engine control)
Ignition switch to the ON position, Accelerator pedal fully released
0.5 to 1.1 V
VTA1 (D1-20) - E2 (D1-28)
R - Y-R
Throttle position sensor
(for engine control)
Ignition switch to the ON position, Accelerator pedal fully depressed
3.3 to 4.9 V
VTA2 (D1-19) - E2 (D1-28)
G - Y-R
Throttle position sensor
(for sensor malfunction detection)
Ignition switch to the ON position, Accelerator pedal fully released
2.1 to 3.1 V
VTA2 (D1-19) - E2 (D1-28)
G - Y-R
Throttle position sensor
(for sensor malfunction detection)
Ignition switch to the ON position, Accelerator pedal fully depressed
4.5 to 5.0 V
VPA (B9-18) - EPA (B9-20)
L - W-L
Accelerator pedal position sensor
(for engine control)
Ignition switch to the ON position, Accelerator pedal fully released
0.5 to 1.1 V
VPA (B9-18) - EPA (B9-20)
L - W-L
Accelerator pedal position sensor
(for engine control)
Ignition switch to the ON position, Accelerator pedal fully depressed
2.6 to 4.5 V
VPA2 (B9-19) - EPA2 (B9-21)
B - W-R
Accelerator pedal position sensor
(for sensor malfunction detection)
Ignition switch to the ON position, Accelerator pedal fully released
1.2 to 2.0 V
VPA2 (B9-19) - EPA2 (B9-21)
B - W-R
Accelerator pedal position sensor
(for sensor malfunction detection)
Ignition switch to the ON position, Accelerator pedal fully depressed
3.4 to 5.0 V
VCPA (B9-26) - EPA (B9-20)
W - W-L
Power source of accelerator pedal position sensor
(for VPA)
Ignition switch to the ON position
4.5 to 5.0 V
VCP2 (B9-27) - EPA2 (B9-21)
R-L - W-R
Power source of accelerator pedal position sensor
(for VPA2)
Ignition switch to the ON position
4.5 to 5.0 V
VG (D3-28) - E2G (D3-30)
Y-G - L-R
Mass air flow meter
Idling, Shift position P or N, A/C switch OFF
0.5 to 3.0 V
THA (D3-29) - E2 (D1-28)
R - Y-R
Intake air temperature sensor
Idling, Intake air temperature 20°C (68 °F)
0.5 to 3.4 V
THW (D1-32) - E2 (D1-28)
R-W - Y-R
Engine coolant temperature sensor
Idling, Intake coolant temperature 80°C (176 °F)
0.2 to 1.0 V
#1 (D3-6) - E01 (D1-7)
#2 (D3-5) - E01 (D1-7)
#3 (D3-2) - E01 (D1-7)
#4 (D3-1) - E01 (D1-7)
B - W-B
B-W - W-B
Y - W-B
R - W-B
Injector
Ignition switch to the ON position
9 to 14 V
#1 (D3-6) - E01 (D1-7)
#2 (D3-5) - E01 (D1-7)
#3 (D3-2) - E01 (D1-7)
#4 (D3-1) - E01 (D1-7)
B - W-B
B-W - W-B
Y - W-B
R - W-B
Injector
Idling
Pulse generation
(see waveform 1)
IGT1 (D1-17) - E1 (D1-3)
IGT2 (D1-16) - E1 (D1-3)
IGT3 (D1-15) - E1 (D1-3)
IGT4 (D1-14) - E1 (D1-3)
R-L - BR
L-W - BR
B-Y - BR
Y-R - BR
Ignition coil with igniter
(ignition coil signal)
Idling
Pulse generation
(see waveform 2)
IGF1 (D1-23) - E1 (D1-3)
W-R - BR
Ignition coil with igniter
(ignition confirmation signal)
Ignition switch to the ON position
4.5 to 5.0 V
IGF1 (D1-23) - E1 (D1-3)
W-R - BR
Ignition coil with igniter
(ignition confirmation signal)
Idling
Pulse generation
(see waveform 2)
G2 (D1-26) - NE- (D1-34)
Y - B
Camshaft position sensor
Idling
Pulse generation
(see waveform 3)
NE+ (D1-27) - NE- (D1-34)
Y - B
Crankshaft position sensor
Idling
Pulse generation
(see waveform 3)
FC (B9-25) - E1 (D1-3)
L-Y - BR
Fuel pump control
Ignition switch to the ON position
9 to 14 V
FC (B9-25) - E1 (D1-3)
L-Y - BR
Fuel pump control
Idling
Below 1.5 V
M+ (D1-5) - ME01 (D3-3)
Y - BR
Throttle actuator
Idling with warm engine
Pulse generation
(see waveform 4)
M- (D1-4) - ME01 (D3-3)
L - BR
Throttle actuator
Idling with warm engine
Pulse generation
(see waveform 5)
A1A+ (D1-21) - E1 (D1-3)
Y - BR
A/F sensor
Always (Ignition switch to the ON position)
3.3 V*1
A1A- (D1-31) - E1 (D1-3)
L - BR
A/F sensor
Always (Ignition switch to the ON position)
3.0 V*1
OX1B (D1-25) - E2 (D1-28)
B - Y-R
Heated oxygen sensor
Engine speed maintained 2,500 rpm for 2 minutes after warming up sensor
Pulse generation
(see waveform 6)
HA1A (D1-1) - E04 (D3-7)
Y - BR
A/F sensor heater
Idling
Below 3.0 V
HA1A (D1-1) - E04 (D3-7)
Y - BR
A/F sensor heater
Ignition switch to the ON position
9 to 14 V
HT1B (D1-2) - E03 (D3-4)
Y - BR
Heated oxygen sensor heater
Idling
Below 3.0 V
HT1B (D1-2) - E03 (D3-4)
Y - BR
Heated oxygen sensor heater
Ignition switch to the ON position
9 to 14 V
KNK1 (D1-29) - EKNK (D1-30)
G - R
Knock sensor
Maintain engine speed 4,000 rpm after warming up
Pulse generation
(see waveform 7)
OC1+ (D1-13) - OC1- (D1-12)
G-B - B-Y
Camshaft timing oil control valve (OCV)
Idling
Pulse generation
(see waveform 8)
PRG (D3-23) - E01 (D1-7)
B - W-B
EVAP VSV
Ignition switch to the ON position
9 to 14 V
PRG (D3-23) - E01 (D1-7)
B - W-B
EVAP VSV
Idling
Pulse generation
(see waveform 9)
STA (B9-12) - E1 (D1-3)
R - BR
Starter signal
Shift position N, ignition switch START
5.5 V or more
STP (B7-4) - E1 (D1-3)
R-W - BR
Stop light switch
Brake pedal depressed
7.5 to 14 V
STP (B7-4) - E1 (D1-3)
R-W - BR
Stop light switch
Brake pedal released
Below 1.5 V
ST1- (B9-16) - E1 (D1-3)
R-L - BR
Stop light switch
Ignition switch to the ON position, Brake pedal depressed
Below 1.5 V
ST1- (B9-16) - E1 (D1-3)
R-L - BR
Stop light switch
Ignition switch to the ON position, Brake pedal released
7.5 to 14 V
W (B7-30) - E01 (D1-7)
G-R - W-B
MIL
Idling
9 to 14 V
W (B7-30) - E01 (D1-7)
G-R - W-B
MIL
Ignition switch to the ON position
Below 3.5 V
ELS (B9-15) - E1 (D1-3)
G - BR
Electric load
Tail light switch ON
7.5 to 14 V
ELS (B9-15) - E1 (D1-3)
G - BR
Electric load
Tail light switch OFF
0 to 1.5 V
TACH (B7-1) - E1 (D1-3)
B-Y - BR
Engine speed
Idling
Pulse generation
(see waveform 10)
SPD (B7-8) - E1 (D1-3)
P-L - BR
Speed signal from combination meter
Driving at 20 km/h (12 mph)
Pulse generation
(see waveform 11)
TC (B7-17) - E1 (D1-3)
P - BR
Terminal TC of DLC 3
Ignition switch to the ON position
9 to 14 V
PSW (D3-32) - E1 (D1-3)
G-W - BR
Power steering oil pressure switch
While turning steering wheel
Below 1.5 V
F/PS (B7-32) - E1 (D1-3)
L - BR
Airbag sensor assembly
Idling with warm engine
Pulse generation
(see waveform 12)
NSW (B9-30) - E1 (D1-3)
B-W - BR
Park/Neutral switch signal
IG switch ON and shift lever in P or N position
Below 1 V
NSW (B9-30) - E1 (D1-3)
B-W - BR
Park/Neutral switch signal
IG switch ON and shift lever in any position except P and N
9 to 14 V
CANH (B7-33) - E1 (D1-3)
B - BR
Communication signal with other components
Ignition switch to the ON position
Pulse generation
(see waveform 13)
CANL (B7-34) - E1 (D1-3)
W - BR
Communication signal with other components
Ignition switch to the ON position
Pulse generation
(see waveform 14)
AIRV (D1-24) - E1 (D1-3)
Y - BR
Air switch valve for secondary air injection system
Idling
9 to 14 V
AIRP (D1-11) - E1 (D1-3)
W-R - BR
Air pump control
Idling
9 to 14 V
AIDI (D3-20) - E1 (D1-3)
LG - BR
Diagnostic information signal for air injection system
Air injection system operates
Pulse generation
(see waveform 15)
*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

WAVEFORM 1


    A093279E03
  1. Fuel injector
    ECM Terminal Names
    Between #1 (to #4) and E01
    Tester Ranges
    20 V/DIV, 20 msec./DIV
    Conditions
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 2


    A093278E05
  1. Igniter IGT signal (from ECM to igniter)

  2. Igniter IGF signal (from igniter to ECM)
    ECM Terminal Names
    1. Between IGT (1 to 4) and E1
    2. Between IGF1 and E1
    Tester Ranges
    2 V/DIV, 20 msec./DIV
    Conditions
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 3


    A063955E01
  1. Camshaft position sensor

  2. Crankshaft position sensor
    ECM Terminal Names
    1. Between G2 and NE-
    2. Between NE+ and NE-
    Tester Ranges
    5 V/DIV, 20 msec./DIV
    Conditions
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 4


    A093274E04
  1. Throttle actuator positive terminal
    ECM Terminal Names
    Between M+ and ME01
    Tester Ranges
    5 V/DIV, 1 msec./DIV
    Conditions
    Idling with warm engine

    HINT:
    The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 5


    A093275E04
  1. Throttle actuator negative terminal
    ECM Terminal Names
    Between M- and ME01
    Tester Ranges
    5 V/DIV, 1 msec./DIV
    Conditions
    Idling with warm engine

    HINT:
    The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 6


    A088863E06
  1. Heated oxygen sensor
    ECM Terminal Names
    Between OX1B and E2
    Tester Ranges
    0.2 V/DIV, 200 msec./DIV
    Conditions
    Engine speed maintained 2,500 rpm for 2 minutes after warming up engine

    HINT:
    In the DATA LIST, item O2S B1S2 shows the input values from the heated oxygen sensor to the ECM.


WAVEFORM 7


    A082985E07
  1. Knock sensor
    ECM Terminal Names
    Between KNK1 and EKNK
    Tester Ranges
    0.01 to 10 V/DIV, 0.01 to 10 msec./DIV
    Conditions
    Engine speed maintained 4,000 rpm after warming up engine

    HINT:
    1. The wavelength becomes shorter as the engine rpm increases.
    2. The waveforms and amplitudes displayed differ slightly depending on the vehicle.


WAVEFORM 8


    A093229E03
  1. Camshaft timing oil control valve (OCV)
    ECM Terminal Names
    Between OC1+ and OC1-
    Tester Ranges
    5 V/DIV, 1 msec./DIV
    Conditions
    idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 9


    A093230E02
  1. EVAP VSV
    ECM Terminal Names
    Between PRG and E01
    Tester Ranges
    5 V/DIV, 50 msec./DIV
    Conditions
    idling

    HINT:
    If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.


WAVEFORM 10


    A093225E02
  1. Engine speed signal
    ECM Terminal Names
    Between TACH and E1
    Tester Ranges
    5 V/DIV, 10 msec./DIV
    Conditions
    idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 11


    A093224E03
  1. Vehicle speed signal
    ECM Terminal Names
    Between SPD and E1
    Tester Ranges
    5 V/DIV, 20 msec./DIV
    Conditions
    Driving at 20 km/h (12 mph)

    HINT:
    The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 12


    A093227E01
  1. Airbag sensor assembly
    ECM Terminal Names
    Between F/PS and E1
    Tester Ranges
    5 V/DIV, 500 msec./DIV
    Conditions
    Idling with warm engine


WAVEFORM 13


    A086154E02
  1. CAN communication signal
    ECM Terminal Names
    Between CANH and E1
    Tester Ranges
    1 V/DIV, 10μs/DIV
    Conditions
    Ignition switch to the ON position


WAVEFORM 14


    A086155E02
  1. CAN communication signal
    ECM Terminal Names
    Between CANL and E1
    Tester Ranges
    1 V/DIV, 10μs/DIV
    Conditions
    Ignition switch to the ON position


WAVEFORM 15


    G037721E01
  1. Terminal DI of air injection control driver
    ECM Terminal Names
    Between AIDI and E1
    Tester Ranges
    5 V/DIV, 100 ms/DIV
    Conditions
    Performing ACTIVE TEST using intelligent tester (air injection system)

    HINT:
    The wavelength changes when the air injection control driver detects malfunctions in the air injection system .