SFI SYSTEM (w/ Secondary Air Injection System) > ECM Power Source Circuit |

| 1.INSPECT ECM (+B VOLTAGE) |
![]() |
Turn the ignition switch to the ON position.
Measure the voltage between the terminals of the ECM connectors.
| Tester Connections | Specified Conditions |
| +B (B9-1) - E1 (D1-3) | 9 to 14 V |
|
| ||||
| NG | |
| 2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND) |
![]() |
Disconnect the negative battery cable.
Disconnect the D1 ECM connector.
Measure the resistance.
| Tester Connections | Specified Conditions |
| E1 (D1-3) - Body ground | Below 1 Ω |
Reconnect the ECM connector.
Reconnect the negative battery cable.
|
| ||||
| OK | |
| 3.INSPECT ECM (IGSW VOLTAGE) |
![]() |
Turn the ignition switch to the ON position.
Measure the voltage between the terminals of the ECM connectors.
| Tester Connections | Specified Conditions |
| IGSW (B9-9) - E1 (D1-3) | 9 to 14 V |
|
| ||||
| NG | |
| 4.CHECK AM2 AND IGN FUSE |
![]() |
Check the AM2 fuse.
Remove the AM2 fuse from the engine room R/B No.2.
Measure the AM2 fuse resistance.
Reinstall the AM2 fuse.
Check the IGN fuse.
Remove the IGN fuse from the instrument panel J/B.
Measure the IGN fuse resistance.
Reinstall the IGN fuse.
|
| ||||
| OK | |
| 5.INSPECT IGNITION SWITCH |
![]() |
Disconnect the I7 ignition switch connector.
Measure the resistance.
| Ignition Switch Positions | Tester Connections | Specified Conditions |
| LOCK | All Terminals | 10 kΩ or higher |
| ACC | 2 - 3 | Below 1 Ω |
| ON | 2 - 3, 2 - 4, 6 - 7 | Below 1 Ω |
| START | 2 - 3, 6 - 7, 1 - 2, 7 - 8 | Below 1 Ω |
Reconnect the ignition switch connector.
|
| ||||
| OK | ||
| ||
| 6.INSPECT MREL VOLTAGE |
![]() |
Turn the ignition switch to the ON position.
Measure the voltage between the terminals of the ECM connectors.
| Tester Connector | Specified Condition |
| MREL (B9-8) - E1 (D1-3) | 9 to 14 V |
|
| ||||
| OK | |
| 7.CHECK EFI FUSE |
![]() |
Remove the EFI fuse from the engine room R/B No.1.
Measure the EFI fuse resistance.
Reinstall the EFI fuse.
|
| ||||
| OK | |
| 8.INSPECT INTEGRATION RELAY (EFI RELAY) |
Remove the integration relay from the engine room R/B No.1.
![]() |
Measure the integration relay (MAIN relay) resistance.
| Tester Connections | Specified Conditions |
| A1 - B4 | 10 kΩ or higher |
| A1 - B4 | Below 1 Ω (when battery voltage applied to terminals B2 and B3) |
Reinstall the integration relay.
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM, INTEGRATION RELAY - BODY GROUND) |
![]() |
Check the harness and connector between the integration relay and the ECM.
Remove the integration relay from the engine room R/B No.1.
Disconnect the B9 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| Integration relay (B2) - MREL (B9-8) | Below 1 Ω |
| Tester Connection | Specified Condition |
| Integration relay (B2) or MREL (B9-8) - Body ground | 10 kΩ or higher |
Reinstall the integration relay.
Reinstall the ECM connector.
Check the harness and connector between the integration relay and the body ground.
Remove the integration relay from the engine room R/B No.1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| Integration relay (B3) - Body ground | Below 1 Ω |
Reinstall the integration relay.
|
| ||||
| OK | ||
| ||