Home › ENGINE ยท 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    P0500/42    Vehicle Speed Sensor "A"

for Preparation Click here


DESCRIPTION

The vehicle speed sensor outputs a 4-pulse signal for every revolution of the rotor shaft, which is rotated by the transmission output shaft via the driven gear. After this signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter, it is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of these pulse signals.

G036461E01


DTC No.
DTC Detection Condition
Trouble Area
P0500/42
  1. Conditions (a), (b) and (c) continue for 7 seconds or more:
    (1 trip detection logic)
    1. Engine coolant temperature is more than 70°C (158°F)
    2. Engine speed is between 2,000 rpm and 3,500 rpm
    3. No speed signal is input to ECM
  1. Open or short in speed sensor circuit
  2. Vehicle speed sensor
  3. Combination meter
  4. ECM

WIRING DIAGRAM


A110960E01


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.


When using intelligent tester:

1.CHECK SPEEDOMETER (SPEEDOMETER OPERATION)
  1. Drive the vehicle.

  1. Check the speedometer reading in the combination meter.

    HINT:
    If the vehicle speed sensor has a malfunction, the speedometer shows abnormal readings.

    OK:
    Speedometer operates normally.



NG
CHECK SPEEDOMETER CIRCUIT (INCLUDE SPEED SENSOR)
OK


2.READ VALUE OF VEHICLE SPEED
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / ECD / Data List / Vehicle Speed.

  1. Check the vehicle speed at an engine speed of 2,000 rpm or more while the vehicle is running.

    OK:
    Same value as actual vehicle speed.



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


3.CHECK ECM TERMINAL VOLTAGE (SPD TERMINAL)


    G036576E01
  1. While idling the engine, check the waveform of the ECM connectors using an oscilloscope.

    1. Jack up the vehicle.

    2. Move the shift lever to N.

    3. Turn the ignition switch ON.

    4. Measure the voltage of the ECM connectors as the rear wheels are turned slowly.

      Standard:
      Tester Connection
      Specified Condition
      B7-17 (SPD) - D3-7 (E1)
      Generated intermittently
      Tool Setting
      5 V/DIV., 20 msec./DIV.
      Condition
      Driving at vehicle speed of 40 km/h (25 mph)

      HINT:
      When the wheels are turned slowly, voltage is output intermittently.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM 


When not using intelligent tester:

1.CHECK SPEEDOMETER (SPEEDOMETER OPERATION)
  1. Drive the vehicle.

  1. Check the speedometer reading in the combination meter.

    HINT:
    If the vehicle speed sensor has any malfunctions, the speedometer shows abnormal readings.

    OK:
    Speedometer operates normally.



NG
CHECK SPEEDOMETER CIRCUIT (INCLUDE SPEED SENSOR)
OK


2.CHECK ECM TERMINAL VOLTAGE (SPD TERMINAL)


    G036576E01
  1. While idling the engine, check the waveform of the ECM connectors using an oscilloscope.

    1. Jack up the vehicle.

    2. Move the shift lever to N.

    3. Turn the ignition switch ON.

    4. Measure the voltage of the ECM connectors as the rear wheels are turned slowly.

      Standard:
      Tester Connection
      Specified Condition
      B7-17 (SPD) - D3-7 (E1)
      Generated intermittently
      Tool Setting
      5 V/DIV., 20 msec./DIV.
      Condition
      Driving at vehicle speed of 40 km/h (25 mph)

      HINT:
      When the wheels are turned slowly, voltage is output intermittently.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM