Home › ENGINE ยท 5L-E › ENGINE CONTROL SYSTEM › ECD SYSTEM

ECD SYSTEM > TERMINALS OF ECM

for Preparation Click here



A002958E01


HINT:
Each ECM terminal's standard normal voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Symbols (Terminal No.)" for the terminals to be inspected. The standard normal voltage between the terminals is shown under "STD Voltage". Use the illustration above as a reference for the ECM terminals.

Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
STD Voltage
BATT (B10-1) - E1 (D2-14)
B-R - BR
Battery (for measuring the battery voltage and for the ECM memory)
Always
9 to 14 V
SREL (B10-2) - E01 (D2-13)
G - BR
Glow plug relay
Cranking
9 to 14 V
SREL (B10-2) - E01 (D2-13)
G - BR
Glow plug relay
Idling
(engine start and after 600 sec.)
0 to 1.5 V
MREL (B10-3) - E1 (D2-14)
G-Y - BR
EFI relay
IG switch ON
9 to 14 V
MREL (B10-3) - E1 (D2-14)
G-Y - BR
EFI relay
IG switch OFF
(after IG switch OFF for 2 sec.)
0 to 1.5 V
TC (B10-4) - E1 (D2-14)
P - BR
Terminal TC of DLC3
IG switch ON
9 to 14 V
W (B10-5) - E1 (D2 -14)
G-R - BR
MIL
Check engine warning light lights up
0 to 3 V
W (B10-5) - E1 (D2-14)
G-R - BR
MIL
Except check engine warning light lights up
9 to 14 V
RFC (B10-7) - E1 (D2-14)
LG-B - BR
Cooling fan ECU
IG switch ON or fan is rotating
Pulse generation
(See waveform 1)
THWO (B10-8) - E1 (D2-14)
Y - BR
Combination meter
IG switch ON
Pulse generation
(See waveform 2)
SPD (B10-9) - E1 (D2-14)
P-L- BR
Speed signal from combination meter
IG switch ON, Rotate driving wheel slowly
Pulse generation
(See waveform 3)
STA (B10 -11) - E1 (D2-14)
R - BR
Starter signal
Cranking
6 V or more
+B (B10 -12) - E1 (D2-14)
B-R - BR
Power source of ECM
IG switch ON
9 to 14 V
FAN (B10-13) - E1 (D2-14)
W-L - BR
Fan relay
Sub fan is rotating
0 to 3 V
FAN (B10-13) - E1 (D2-14)
W-L - BR
Fan relay
Sub fan is not rotating
9 to 14 V
IGSW (B10-14) - E1 (D2-14)
B-R - BR
Engine switch
IG switch ON
9 to 14 V
SIL (B10-15) - E1 (D2-14)
W - BR
Terminal SIL of DLC3
Connect intelligent tester to DLC3
Pulse generation
STP (B10-19) - E1 (D2-14)
R-W - BR
Stop light switch
Brake pedal depressed
9 to 14 V
STP (B10-19) - E1 (D2-14)
R-W - BR
Stop light switch
Brake pedal released
Below 1.5 V
HSW (B10-20) - E1 (D2-14)
L-W - BR
Idle up switch
Idle up switch ON
Below 2.5 V
HSW (B10-20) - E1 (D2-14)
L-W - BR
Idle up switch
Idle up switch OFF
9 to 14 V
ALT (B10-22) - E1 (D2-14)
W - BR
Generator (alternator) duty ratio
Idling
Pulse generation
(See waveform 4)
GIND (B8-1) - E1 (D2-14)
B-W - BR
Glow indicator light
Glow indicator light lights up
0 to 3 V
GIND (B8-1) - E1 (D2-14)
B-W - BR
Glow indicator light
Except glow indicator light lights up
9 to 14 V
AC1 (B8-2) - E1 (D2-14)
R-B - BR
A/C amplifier
A/C switch ON
(at magnet clutch ON)
Below 1.5 V
AC1 (B8-2) - E1 (D2-14)
R-B - BR
A/C amplifier
A/C switch OFF
7.5 to 14 V
VPA (B8-5) - EPA (B8-4)
L - W-L
Accelerator pedal position sensor
(for engine control)
IG switch ON, accelerator pedal released
0.5 to 1.1 V
VPA (B8-5) - EPA (B8-4)
L - W-L
Accelerator pedal position sensor
(for engine control)
IG switch ON, accelerator pedal depressed
2.6 to 4.5 V
VCPA (B8-6) - EPA (B8-4)
W - W-L
Power source of accelerator pedal position sensor
(for VPA)
IG switch ON
4.5 to 5.5 V
TACH (B8-7) - E1 (D2-14)
B-Y - BR
Engine speed
Idling
Pulse generation
(See waveform 5)
ACT (B8-8) - E1 (D2-14)
G-W - BR
A/C amplifier
IG switch ON
9 to 14 V
ACT (B8-8) - E1 (D2-14)
G-W - BR
A/C amplifier
At A/C cut controlled (Driving below 30 km/h (18.6 mph), accelerator pedal fully depressed for 5 sec.)
0 to 3 V
ST1 - (B8-11) - E1 (D2-14)
R-L - BR
Stop light switch
Brake pedal depressed
Below 1.5 V
ST1 - (B8-11) - E1 (D2-14)
R-L - BR
Stop light switch
Brake pedal released
9 to 14 V
VPA2 (B8-12) - EPA (B8-4)
B - W-L
Accelerator pedal position sensor (for sensor malfunction detection)
IG switch ON, accelerator pedal released
1.2 to 2.0 V
VPA2 (B8-12) - EPA (B8-4)
B - W-L
Accelerator pedal position sensor (for sensor malfunction detection)
IG switch ON, accelerator pedal depressed
3.4 to 5.3 V
VC (D4-1) - E2 (D4-9)
L-B - Y-R
Power source of sensor (a specific voltage)
IG switch ON
4.5 to 5.5 V
PIM (D4-2) - E2 (D4-9)
P - Y-R
Pressure sensor
Apply vacuum 60 kPa
(450 mmHg, 17.7 in.Hg)
0.2 to 0.8 V
PIM (D4-2) - E2 (D4-9)
P - Y-R
Pressure sensor
Apply vacuum 207 kPa
(1,550 mmHg, 61.0 in.Hg)
4.2 to 4.8 V
THA (D4-3) - E2 (D4-9)
R-L - Y-R
Intake air temperature sensor
Idling, air intake temp. 0°C (32°F) to 80°C (176°F)
0.5 to 3.4 V
THW (D4-4) - E2 (D4-9)
R-W - Y-R
Engine coolant temperature sensor
Idling, engine coolant temp. 60°C (140°F) to 120°C (248°F)
0.2 to 1.0 V
THF (D4-5) - E2 (D4-9)
R - Y-R
Fuel temperature sensor
IG switch ON (at engine cold)
0.5 to 3.4 V
DATA (D4-6) - E1 (D2-14)
Y - BR
Injection pump
For 0.5 sec. after IG switch ON
Pulse generation
PR2 (D4-8) - E1 (D2-14)
Y-G - BR
Pressure switch
Pressure switch ON (A/C pressure is normal)
Below 1.5 V
PR2 (D4-8) - E1 (D2-14)
Y-G - BR
Pressure switch
Pressure switch OFF (A/C pressure is low)
9 to 14 V
RTHW (D4-12) - E2 (D4-9)
L-R - Y-R
Radiator side engine coolant temperature sensor
Idling, radiator side engine coolant temp. 60°C (140°F) to 120°C (248°F)
0.2 to 1.0 V
CLK (D4-14) - E1 (D2-14)
L - Y-R
Injection pump
For 0.5 sec. after IG switch ON
Pulse generation
THOP (D4-15) - E1 (D2-14)
L - BR
Intake shutter fully opened switch
Idling (engine warmed up)
9 to 14 V
THOP (D4-15) - E1 (D2-14)
L - BR
Intake shutter fully opened switch
IG switch ON (once within 5 sec.)
0 to 3 V
LU-B (D2-7) - E01 (D2-13)
G - BR
Intake restrictor valve control motor
(Intake shutter)
Racing (engine warmed up)
Pulse generation
(See waveform 6)
LU+B (D2-8) - E01 (D2-13)
R - BR
Intake restrictor valve control motor
(Intake shutter)
Racing (engine warmed up)
Pulse generation
(See waveform 6)
LU-A (D2-9) - E01 (D2-13)
W - BR
Intake restrictor valve control motor
(Intake shutter)
Racing (engine warmed up)
Pulse generation
(See waveform 6)
LU+A (D2-10) - E01 (D2-13)
B - BR
Intake restrictor valve control motor
(Intake shutter)
Racing (engine warmed up)
Pulse generation
(See waveform 6)
TCV (D2-11) - E01 (D2-13)
B-W - BR
Timing control valve
IG switch ON
9 to 14 V
TCV (D2-11) - E01 (D2-13)
B-W - BR
Timing control valve
Idling
Pulse generation
(See waveform 7)
SPV+ (D2-12) - E1 (D2-14)
B - BR
Spill control valve
IG switch ON
9 to 14 V
SPV+ (D2-12) - E1 (D2-14)
B - BR
Spill control valve
Idling
Pulse generation
TDC+ (D2-17) - TDC- (D2-16)
R - G
Crankshaft position sensor
Idling
Pulse generation
(See waveform 8)
NE+ (D2-19) - NE- (D2-18)
Y - L
Engine speed sensor
Idling
Pulse generation
(See waveform 8)
SPV- (D2-25) - E1 (D2-14)
B-L - BR
Spill control valve
Idling
Pulse generation
(See waveform 9)


Waveform 1 (Reference):


    A111767E01
  1. Cooling fun signal.
    Terminal
    RFC - E1
    Tool Setting
    1 V/DIV., 2 ms/DIV.
    Condition
    When fan operating

    HINT:
    Waveform time A changes according to coolant temperature.


Waveform 2 (Reference):


    A105099E01
  1. A/C amplifier signal.
    Terminal
    THWO - E1
    Tool Setting
    5 V/DIV., 0.1 s/DIV.
    Condition
    During idling

    HINT:
    Waveform time A changes according to coolant temperature.


Waveform 3 (Reference):


    A110545E01
  1. Speed signal.
    Terminal
    SPD - E1
    Tool Setting
    2 V/DIV., 20 ms/DIV.
    Condition
    When driving at approx. 20 km/h (12.4 mph).

    HINT:
    1. As vehicle speed increases, the waveform becomes shorter.
    2. As vehicle speed increases, the waveforms amplitude become greater.


Waveform 4 (Reference):


    A105102E01
  1. Generator signal.
    Terminal
    ALT - E1
    Tool Setting
    5 V/DIV., 5 ms/DIV.
    Condition
    During idling


Waveform 5 (Reference):


    A110546E01
  1. Engine speed signal.
    Terminal
    TACH - E1
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    1. After warming up
    2. During idling

    HINT:
    As engine speed increases, the waveform becomes shorter.


Waveform 6 (Reference):


    A110547E01
  1. Intake restrictor valve control motor signal.
    Terminal
    LU+A, LU-A, LU+B, LU-B - E01
    Tool Setting
    10 V/DIV., 0.5 ms/DIV.
    Condition
    During engine racing


Waveform 7 (Reference):


    A002482E01
  1. Timing control value signal.
    Terminal
    TCV - E01
    Tool Setting
    10 V/DIV., 10 ms/DIV.
    Condition
    During idling


Waveform 8 (Reference):


    A002483E01
  1. Crankshaft position sensor signal.
    Terminal
    TDC+ - TDC-
    NE+ - NE-
    Tool Setting
    2 V/DIV., 20 ms/DIV.
    Condition
    During idling


Waveform 9 (Reference):


    A110550E01
  1. Spill control valve signal.
    Terminal
    SPV- - E1
    Tool Setting
    20 V/DIV., 10 ms/DIV.
    Condition
    During idling