Home › ENGINE · 5L-E › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    51    Stop Light Switch Circuit Malfunction

for Preparation Click here


DESCRIPTION

In this system, the signal of the stop light switch is used to judge whether the stop light system is abnormal or not.
The stop light switch has a duplex system (signals STP and ST1-) to memorize the abnormality when the signals of depressing and releasing the brake pedal are detected simultaneously.

HINT:
Normal condition is as shown in the table.

Signal
Brake pedal released
In transition
Brake pedal depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF

DTC No.
DTC Detection Condition
Trouble Area
51
When STP (without depressing the brake pedal) and ST1- (with the brake pedal depressed) signals continue for longer than 0.5 seconds with the ignition switch ON
  1. Open or short in stop light switch signal circuit
  2. Stop light switch
  3. ECM


WIRING DIAGRAM


A106785E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


When using intelligent tester:

1.READ VALUE OF INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON.

  1. Select the item "Powertrain/Engine and ECT/Data List/Stop Light SW" and read its value displayed on the intelligent tester.

    OK:

    Brake Pedal
    Display
    Depressed
    Stop Light SW ON
    Repressed
    Stop Light SW OFF



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS 

2.INSPECT ECM


    A110540E01
  1. Turn the ignition switch ON.

  1. Measure the voltage between the terminals of the ECM connector.

    Standard voltage (Brake pedal is depressed):
    Tester Connection
    Specified Condition
    STP (B10-19) - E1 (D2-14)
    9 to 14 V
    ST1- (B8-11) - E1 (D2-14)
    Below 1.5 V

    Standard voltage (Brake pedal is released):
    Tester Connection
    Specified Condition
    STP (B10-19) - E1 (D2-14)
    Below 1.5 V
    ST1- (B8-11) - E1 (D2-14)
    9 to 14 V



NG
Go to step 3
OK

REPLACE ECM 

3.INSPECT STOP LIGHT SWITCH


    A072924E02
  1. Disconnect the stop light switch connector.

  1. Check the resistance between each pair of the terminals.

    Standard resistance:
    Switch Position
    Tester Connection
    Specified Condition
    Switch pin free
    3 - 4
    Below 1 Ω
    Switch pin pushed in
    3 - 4
    10 kΩ or higher
    Switch pin free
    1 - 2
    10 kΩ or higher
    Switch pin pushed in
    1 - 2
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH
OK


4.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH)


    A110541E01
  1. Disconnect the stop light switch connector.

  1. Disconnect the ECM B8 and B10 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    (B2-1) - STP (B10-19)
    Below 1 Ω
    (B2-4) - ST1- (B8-11)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    STP (B10-19) - Body ground
    10 kΩ or higher
    ST1- (B8-11) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE POWER SOURCE CIRCUIT 


When not using intelligent tester:

1.CHECK OPERATION OF STOP LIGHT
  1. Check if the stop lights go on and off normally when the brake pedal is depressed and released.

    OK:
    The stop lights go on and off normally.



NG
REPAIR STOP LIGHT SWITCH CIRCUIT
OK


2.INSPECT ECM


    A110540E01
  1. Turn the ignition switch ON.

  1. Measure the voltage between the terminals of the ECM connector.

    Standard voltage (Brake pedal is depressed):
    Tester Connection
    Specified Condition
    STP (B10-19) - E1 (D2-14)
    9 to 14 V
    ST1- (B8-11) - E1 (D2-14)
    Below 1.5 V

    Standard voltage (Brake pedal is released):
    Tester Connection
    Specified Condition
    STP (B10-19) - E1 (D2-14)
    Below 1.5 V
    ST1- (B8-11) - E1 (D2-14)
    9 to 14 V



NG
Go to step 3
OK

REPLACE ECM 

3.INSPECT STOP LIGHT SWITCH


    A072924E02
  1. Disconnect the stop light switch connector.

  1. Check the resistance between each pair of the terminals.

    Standard resistance:
    Switch Position
    Tester Connection
    Specified Condition
    Switch pin free
    3 - 4
    Below 1 Ω
    Switch pin pushed in
    3 - 4
    10 kΩ or higher
    Switch pin free
    1 - 2
    10 kΩ or higher
    Switch pin pushed in
    1 - 2
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH
OK


4.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH)


    A110541E01
  1. Disconnect the stop light switch connector.

  1. Disconnect the ECM B8 and B10 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    (B2-1) - STP (B10-19)
    Below 1 Ω
    (B2-4) - ST1- (B8-11)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    STP (B10-19) - Body ground
    10 kΩ or higher
    ST1- (B8-11) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE POWER SOURCE CIRCUIT