Home › ENGINE · 5L-E › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    14    Timing Control System Malfunction

for Preparation Click here


DESCRIPTION

The ECM controls the injection timing by actuating the timing control valve. The timing control valve is mounted on the injection pump and delay one by dutys control of pump internal fuel pressure.
The ECM detects the injection advance angle by TDC and NE signals.

DTC No.
DTC Detection Condition
Trouble Area
14
During and after engine warm up, actual injection timing is different from target value of ECM calculated for several sec.
  1. Open or short in timing control valve circuit
  2. Timing control valve
  3. Fuel filter (Clogging)
  4. Fuel (Freezing, Air in)
  5. Injection pump (Internal pressure and timing control valve)
  6. ECM

WIRING DIAGRAM


A106782E01


INSPECTION PROCEDURE

1.INSPECT TIMING CONTROL VALVE


    A105093E01
  1. Disconnect the timer control valve connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    10 to 14 Ω (20°C (68°F))



NG
REPLACE TIMING CONTROL VALVE
OK


2.INSPECT ECM (CHECK VOLTAGE)


    A062420E01
  1. Disconnect the ECM D2 connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    TCV (D2-11) - Body ground
    9 to 14 V



NG
Go to step 6
OK


3.INSPECT ECM


    A106826E01
  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    TCV (D2-11) - E1 (D2-14)
    9 to 14 V

  1. While idling, measure the waveform according to the value( s) in the table below.

    OK:
    Tester Connection
    Specified Condition
    TCV (D2-11) - E1 (D2-14)
    Correct waveform shown



NG
REPLACE ECM
OK


4.CHECK FUEL FILTER ASSEMBLY


NG
REPLACE FUEL FILTER ASSEMBLY
OK


5.CHECK FUEL LEAKAGE
  1. Visually check the injection pump, each injector and fuel line for fuel leaks.

    OK:
    No leakage



NG
REPAIR OR REPLACE FUEL LEAKAGE
OK

CHECK AND REPLACE INJECTION PUMP ASSEMBLY 

6.INSPECT TIMING CONTROL VALVE (POWER SOURCE)


    A073804E01
  1. Disconnect the timing control valve connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    B (D61-1) - Body ground
    9 to 14 V



NG
Go to step 7
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (TIMING CONTROL VALVE - ECM) 

7.CHECK HARNESS AND CONNECTOR (ECM - MAIN RELAY)


    A106815E01
  1. Disconnect the timing control valve connector.

  1. Disconnect the ECM D2 connector.

  1. Disconnect the integration relay 1J connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    B (D61-1) - (1J-4)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    TCV (D2-11) - Body ground
    10 kΩ or higher
    B (D61-1) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK FOR ECM POWER SOURCE CIRCUIT