Home › ENGINE · 5L-E › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    23    Air Temperature Circuit Malfunction

for Preparation Click here


DESCRIPTION

The intake air temperature sensor senses the intake air temperature. A thermistor built in this sensor changes the resistance value according to the intake air temperature as shown in the illustration. This resistance value of intake air temperature sensor is one of the factors to decide the fuel injection volume.
A071307E01

DTC No.
DTC Detection Condition
Trouble Area
23
Open or short in intake air temperature sensor circuit for 0.5 sec. or more
  1. Open or short in intake air temperature sensor circuit
  2. Intake air temperature sensor
  3. ECM

WIRING DIAGRAM


A110556E01


INSPECTION PROCEDURE

HINT:
  1. If different DTCs that are related to different systems are output simultaneously while terminal E2 is used as a ground terminal, terminal E2 may be open.
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


When using intelligent tester:

1.READ VALUE OF INTELLIGENT TESTER (INTAKE AIR TEMPERATURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON.

  1. Select the item "Powertrain/Engine and ECT/Data List/Intake Air" and read its value displayed on the intelligent tester.

    Result:

    Display
    Proceed
    - 40°C (- 40°F)
    A
    140°C (284°F) or more
    B
    The same as actual engine coolant temperature
    C


    HINT:
    When DTC 23 is present, check the intake air temperature by selecting "Powertrain/Engine and ECT/Data List/Intake Air" on the intelligent tester.

    Temperature displayed
    Malfunction
    - 40°C (- 40°F)
    Open circuit
    140°C (284°F) or more
    Short circuit



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS
A


2.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN)


    A110535E01
  1. Disconnect the intake air temperature sensor connector.

  1. Connect the terminals 1 and 2 of the intake air temperature sensor harness side connector.

  1. Turn the ignition switch ON.

  1. Read the temperature value on the intelligent tester.

    Temperature:
    140°C (284°F) or more



NG
Go to step 3
OK

REPLACE INTAKE AIR TEMPERATURE SENSOR 

3.INSPECT ECM (CHECK FOR OPEN)


    A110532E01
  1. Connect between terminals THA and E2 of the ECM connector.

  1. Turn the ignition switch ON.

  1. Read the temperature value on the intelligent tester.

    Temperature:
    140°C (284°F) or more



NG
REPLACE ECM
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)


    A076591E02
  1. Disconnect the intake air temperature sensor connector.

  1. Turn the ignition switch ON.

  1. Read the temperature value on the intelligent tester.

    Temperature:
    -40°C (-40°F) or more



NG
Go to step 5
OK

REPLACE INTAKE AIR TEMPERATURE SENSOR 

5.INSPECT ECM (CHECK FOR SHORT)


    A110533E01
  1. Disconnect the ECM D4 connector.

  1. Turn the ignition switch ON.

  1. Read the temperature value on the intelligent tester.

    Temperature:
    -40°C (-40°F) or more



NG
REPLACE ECM
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 


When not using intelligent tester:

1.INSPECT ECM


    A062416E07
  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    THA (D4-3) - E2 (D4-9)
    0.2 to 3.8 V (20°C (68°F))
    THA (D4-3) - E2 (D4-9)
    0.1 to 1.5 V (80°C (176°F))



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS 

2.INSPECT INTAKE AIR TEMPERATURE SENSOR


    A105096E01
  1. Measure the resistance according to the illustration.

    OK:
    The resistance value is within the acceptable range shown in the illustration.



NG
REPLACE INTAKE AIR TEMPERATURE SENSOR
OK


3.CHECK HARNESS AND CONNECTOR (ECM - INTAKE AIR TEMPERATURE SENSOR)


    A110536E01
  1. Disconnect the intake air temperature sensor connector.

  1. Disconnect the ECM D4 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    THA (A2-2) - THA (D4-3)
    Below 1 Ω
    E2 (A2-1) - E2 (D4-9)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    THA (D4-3) - E2 (D4-9)
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM