Home › ENGINE · 5L-E › ENGINE CONTROL SYSTEM › ECD SYSTEM

ECD SYSTEM > ECM Power Source Circuit

for Preparation Click here


DESCRIPTION

When the ignition switch is turned ON, battery positive voltage is applied to the coil, closing the contacts of the MAIN relay (Marking: MAIN) and supplying power to the terminal +B of the ECM.

WIRING DIAGRAM


A106786E01


INSPECTION PROCEDURE

1.INSPECT ECM (CHECK VOLTAGE)


    A062416E11
  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    +B (B10-12) - E1 (D2-14)
    9 to 14 V



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE 

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)


    A062420E03
  1. Disconnect the ECM D2 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    E1 (D2-14) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT INTEGRATION RELAY (MAIN RELAY)


    A106791E01
  1. Check that operation sound is heard from the integration relay (MAIN relay) in connection with the operation (on/off) of the ignition switch.

    OK:
    Operation sound can be heard.



NG
Go to step 5
OK


4.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)


    A106816E01
  1. Disconnect the battery negative cable.

  1. Disconnect the battery positive cable.

  1. Disconnect the engine room R/B & J/B No.1 1B, 1J and 1K connectors.

  1. Disconnect the engine room R/B & J/B No.1 1D connector.

  1. Disconnect the ECM B10 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    +B (B10-12) - (1J-4)
    Below 1 Ω
    (1K-1) - (1B-3)
    Below 1 Ω
    (1D-1) - Positive terminal of the battery
    Below 1 Ω

    NOTICE:
    After reconnecting the battery cable, the radio and clock should be adjusted as they were previously.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INTEGRATION RELAY 

5.INSPECT ECM (CHECK VOLTAGE)


    A062416E12
  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    MREL (B10-3) - E1 (D2-14)
    9 to 14 V



NG
Go to step 7
OK


6.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)


    A106817E01
  1. Disconnect the ECM B10 connector.

  1. Disconnect the engine room R/B & J/B No.1 1J connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    MREL (B10-3) - (1J-2)
    Below 1 Ω
    (1J-3) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INTEGRATION RELAY 

7.INSPECT ECM (CHECK VOLTAGE)


    A062416E13
  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value (s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    IGSW (B10-14) - E1 (D2-14)
    9 to 14 V



NG
Go to step 8
OK

REPLACE ECM 

8.CHECK FUSE (IGN FUSE)


    A106792E01
  1. Remove the IGN fuse from the instrument panel J/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    IGN fuse
    Below 1 Ω (Continuity)



NG
REPLACE FUSE (IGN FUSE)
OK


9.INSPECT IGNITION SWITCH


    A058559E01
  1. Disconnect the ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Ignition switch position is LOCK):
    Tester Connection
    Specified Condition
    All terminals
    10 kΩ or higher

    Standard resistance (Ignition switch position is ACC):
    Tester Connection
    Specified Condition
    2 - 3
    Below 1 Ω

    Standard resistance (Ignition switch position is ON):
    Tester Connection
    Specified Condition
    2 - 3 - 4
    Below 1 Ω
    6 - 7
    Below 1 Ω

    Standard resistance (Ignition switch position is START):
    Tester Connection
    Specified Condition
    1 - 2 - 4
    Below 1 Ω
    7 - 8
    Below 1 Ω



NG
REPLACE IGNITION SWITCH
OK

CHECK AND REPLACE HARNESS AND CONNECTOR (ECM - BATTERY)