Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM (w/ Secondary Air Injection System)

DTC    P0443    Evaporative Emission Control System Purge Control Valve Circuit

for Preparation Click here


DESCRIPTION

In order to reduce hydrocarbon (HC) emissions, evaporated fuel from the fuel tank is routed through the charcoal canister to the intake manifold for combustion in the cylinders.
The ECM changes the duty signal to the EVAP VSV so that the intake of HC emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No.
DTC Detection Condition
Trouble Area
P0443
Proper response to ECM command does not occur
(1 trip detection logic)
  1. Open or short in EVAP VSV circuit
  2. EVAP VSV
  3. ECM

WIRING DIAGRAM


A111666E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.PERFORM ACTIVE TEST BY INTELLIGENT TESTER (EVAP VSV)


    A080362E02
  1. Disconnect the vacuum hose of the EVAP VSV.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the intelligent tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT /Active Test / Activate the VSV for EVAP Control.

  1. Check if the disconnected port applies suction to your finger when operating the EVAP VSV using the intelligent tester.

    Standard:
    Tester Operation
    Specified condition
    VSV is ON
    Applies suction to your finger
    VSV is OFF
    Applies no suction to your finger

  1. Reconnect the vacuum hose.



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


2.INSPECT ECM (CHECK VOLTAGE)


    A018294E27
  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Voltage:
    Tester Connection
    Specified Condition
    PRG (D3-23) - E01 (D1-7)
    9 to 14 V



OK
REPLACE ECM
NG


3.CHECK OPERATION OF EVAP VSV

OK:
Air flows when the battery voltage is applied to the EVAP VSV.



NG
REPLACE EVAP VSV
OK


4.CHECK HARNESS AND CONNECTOR (ECM - EVAP VSV)


    A110500E01
  1. Disconnect the D3 ECM connector.

  1. Disconnect the D28 EVAP VSV connector.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance (Check for open):
    Tester Connection
    Specified Condition
    EVAP VSV (D28-1) - PRG (D3-23)
    Below 1 Ω

    Resistance (Check for short):
    Tester Connection
    Specified Condition
    EVAP VSV (D28-1) or PRG (D3-23) -
    Body ground
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the EVAP VSV connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (EVAP VSV - INTEGRATION RELAY)


    A111147E01
  1. Remove the integration relay from the engine room R/B No.1.

  1. Disconnect the D28 EVAP VSV connector.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance (Check for open):
    Tester Connection
    Specified Condition
    EVAP VSV (D28-2) - integration relay (B4)
    Below 1 Ω

    Resistance (Check for short):
    Tester Connection
    Specified Condition
    EVAP VSV (D28-2) or integration relay (B4) - Body ground
    10 kΩ or higher

  1. Reinstall the integration relay.

  1. Reconnect the EVAP VSV connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

INSPECT ECM POWER SOURCE CIRCUIT