Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM (w/ Secondary Air Injection System)

DTC    P0504    Brake Switch "A" / "B" Correlation

for Preparation Click here


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and sets the DTC.

HINT:
The normal conditions are as shown in the table below. The signals can be read using an intelligent tester.

Signals
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF


DTC No.
DTC Detection Conditions
Trouble Areas
P0504
  1. Conditions (a), (b) and (c) continue for 0.5 seconds or more
    (1 trip detection logic):
    1. Ignition switch ON
    2. Brake pedal released
    3. STP signal OFF when ST1- signal OFF
  1. Short in stop light switch signal circuit
  2. STOP fuse
  3. Stop light switch
  4. ECM

WIRING DIAGRAM


A111668E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK OPERATION OF STOP LIGHT
  1. Check whether the stop lights turn on and off normally when the brake pedal is depressed and released.

    OK:
    Stop lights turn ON when brake pedal is depressed.



NG
REPAIR OR REPLACE STOP LIGHT SWITCH CIRCUIT
OK


2.INSPECT STOP LIGHT SWITCH ASSEMBLY


    A072924E06
  1. Remove the stop light switch assembly.

  1. Measure the resistance.

    Resistance:
    Switch Positions
    Tester Connections
    Specified Conditions
    Switch pin free
    1 - 2
    Below 1 Ω
    Switch pin free
    3 - 4
    10 kΩ or higher
    Switch pin pushed in
    1 - 2
    10 kΩ or higher
    Switch pin pushed in
    3 - 4
    Below 1 Ω

  1. Reinstall the stop light switch assembly.



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


3.READ VALUE OF INTELLIGENT TESTER (STP SIGNAL AND ST1- VOLTAGE)


    A093220E01
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Stop Light SW.

  1. Check the STP signal when the brake pedal is depressed and released.

    Standard:
    Brake Pedal Operations
    Specified Conditions
    Depressed
    STP signal ON
    Released
    STP signal OFF

  1. Measure the voltage between the terminals of the ECM connectors.

    Voltage:
    Tester Connections
    Brake Pedal Operations
    Specified Conditions
    ST1- (B9-16)
    - E1 (D1-3)
    Depressed
    Below 1.5 V
    ST1- (B9-16)
    - E1 (D1-3)
    Released
    7.5 to 14 V



NG
Go to step 4
OK

CHECK FOR INTERMITTENT PROBLEMS 

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)


    A110515E01
  1. Disconnect the B2 stop light switch connector.

  1. Disconnect the B7 and B9 ECM connectors.

  1. Measure the resistance.

    Resistance (Check for open):
    Tester Connections
    Specified Conditions
    Stop light switch (B2-1) - STP (B7-4)
    Below 1 Ω
    Stop light switch (B2-4) - ST1- (B9-16)
    Below 1 Ω

  1. Reconnect the stop light switch connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM