Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM (w/ Secondary Air Injection System)

DTC    P0560    System Voltage

for Preparation Click here


MONITOR DESCRIPTION

The battery supplies power to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, these memories are cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and sets the DTC.

DTC No.
DTC Detection Conditions
Trouble Areas
P0560
Open in ECM back up power source circuit
(1 trip detection logic)
  1. Open in back up power source circuit
  2. EFI fuse
  3. ECM

HINT:
If DTC P0560 is set, the ECM does not store other DTCs.


WIRING DIAGRAM


A111669E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK EFI FUSE


    A102921E01
  1. Remove the EFI fuse from the engine room R/B No.1.

  1. Measure the resistance.

    Resistance:
    Below 1 Ω

  1. Reinstall the EFI fuse.



NG
REPLACE EFI FUSE
OK


2.INSPECT ECM (BATT VOLTAGE)


    A065741E07
  1. Measure the voltage between the terminals of the ECM connectors.

    Voltage:
    Tester Connections
    Specified Conditions
    BATT (B9-3) - E1 (D1-3)
    9 to 14 V



NG
Go to step 3
OK

REPLACE ECM 

3.CHECK HARNESS AND CONNECTOR (ECM - EFI FUSE, EFI FUSE - BATTERY)


    A111148E01
  1. Check the harness and the connector between the EFI fuse and ECM.

    1. Remove the EFI fuse from the engine room R/B No.1.

    2. Disconnect the B9 ECM connector.

    3. Measure the resistance.

      Resistance (Check for open):
      Tester Connections
      Specified Conditions
      EFI fuse (2) - BATT (B9-3)
      Below 1 Ω

      Resistance (Check for short):
      Tester Connections
      Specified Conditions
      EFI fuse (2) or BATT (B9-3) - Body ground
      10 kΩ or higher

    4. Reconnect the ECM connector.

    5. Reinstall the EFI fuse.

  1. Check the harness and the connector between the EFI fuse and battery.

    1. Remove the EFI fuse from the engine room R/B.

    2. Disconnect the positive battery cable.

    3. Measure the resistance.

      Resistance (Check for open):
      Tester Connections
      Specified Conditions
      Battery positive cable - EFI fuse (1)
      Below 1 Ω

      Resistance (Check for short):
      Tester Connections
      Specified Conditions
      Battery positive cable or EFI fuse (1)
      - Body ground
      10 kΩ or higher

    4. Reconnect the positive battery terminal.

    5. Reinstall the EFI fuse.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT BATTERY
  1. Check that the battery is not depleted.



NG
REPLACE BATTERY
OK

CHECK AND REPLACE ENGINE ROOM RELAY BLOCK