Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM (w/ Secondary Air Injection System)

DTC    P0412    Secondary Air Injection System Switching Valve "A" Circuit

for Preparation Click here


DESCRIPTION

The Secondary Air Injection (AI) system consists of an air pump, Air Switching Valve (ASV), Air Injection Control Driver (AID) and the ECM. After the cold engine starts, the AI system pumps the secondary air to the exhaust port of the cylinder head to purify the exhaust emissions.
The ECM transmits command signals to the AID to drive the ASV and the air pump, and the AID drives them.
The pressure sensor detects a pressure in the secondary air passage when the AI system is ON and OFF, and sends the pressure signal to the ECM.
The function of AID is not only pump and valve driving, but also diagnosis function to detect malfunctions in the AI system circuit.

HINT:
A large amount of current is required to drive the air pump and ASV so that an air injection control driver is provided newly on the previous system.


G038628E01


DTC No.
DTC Detection Conditions
Trouble Areas
P0412
  1. After cold engine starts, all of following conditions are met
    (1 trip detection logic):
    1. Air injection System not operate (Air pump OFF and Air Switching Valve OFF)
    2. Diagnostic signal from Air Injection Control Driver 40 %
    3. Battery voltage 8 V or more
  1. Open in air switching valve circuit and +B circuit
  2. Air Injection driver
  3. Air switching valve
  4. ECM
P0412
  1. After cold engine starts, all of following conditions are met
    (1 trip detection logic):
    1. While Air Injection System operating (Air pump ON and Air Switching Valve ON)
    2. Diagnostic signal from Air Injection Driver 40 %
    3. Battery voltage 8 V or more
  1. Short between air switching valve circuit and body ground
  2. Air Injection driver
  3. Air switching valve
  4. ECM

MONITOR DESCRIPTION

Air Injection Control Driver detects an open or short in the air pump and Air Switching Valve circuit according to the terminal voltage and sends a signal as the diagnostic information to the ECM.
After the cold engine starts, the ECM transmits command signals to the Air Injection Driver the air pump and Air Switching Valve.
The Air Injection Driver outputs the Air Switching Valve malfunction signal to the ECM if: 1) the voltage of Air Injection Driver terminal for Air Switching Valve is low despite the Air injection Driver receiving the command signal from the ECM to drive the Air Switching Valve or 2) the voltage of Air Injection Driver terminal for Air Switching Valve is high despite the Air Injection Driver not receiving the command signal from ECM.
The ECM sets the DTC based on the diagnostic signal from the Air Injection Driver.

WIRING DIAGRAM


A111665E02


INSPECTION PROCEDURE

HINT:
The diagnostic information output from the AID can be confirmed by connecting an oscilloscope to the diagnostic information terminal of the AID.


  1. A065741E06
    Connect the intelligent tester to the DLC3.
  2. Connect an oscilloscope probe to the AIDI terminal of the ECM.
  3. Start the engine and turn the tester ON.

  4. Monitor the voltage output of the AID (duty ratio signal).

    Oscilloscope range: 
    Items
    Contents
    Terminals
    CH1: AIDI (D3-20) - E1 (D1-3)
    Equipment Settings
    5 V/Division, 20 to 40 ms/Division
    Conditions
    Idling


    A111145E02



    A111146E02

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.INSPECT AIR SWITCHING VALVE ASSEMBLY


    G037724E01
  1. Disconnect the D30 ASV connector.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    E (D30-1) - VV (D30-2)
    4.5 to 5.5 Ω

  1. Reconnect the ASV connector.



NG
REPLACE AIR SWITCHING VALVE ASSEMBLY
OK


2.CHECK HARNESS AND CONNECTOR (AIR SWITCHING VALVE ASSEMBLY - BODY GROUND)


    A056870E01
  1. Disconnect the D30 ASV connector.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    E (D30-1) - Body ground
    Below 1 Ω

  1. Reconnect the ASV connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (AIR SWITCHING VALVE ASSEMBLY - AIR INJECTION CONTROL DRIVER)


    A110495E01
  1. Disconnect the D30 ASV connector.

  1. Disconnect the B12 AID connector.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    VV (D30-2) - VV (B12-6)
    Below 1 Ω

  1. Reconnect the ASV connector.

  1. Reconnect the AID connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR INJECTION CONTROL DRIVER