Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Short in CAN Bus Lines

for Preparation Click here


DESCRIPTION

The CAN bus lines are considered to be shorted when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
  1. Short in CAN bus lines
  2. ECM
  3. Air conditioning amplifier
  4. CAN J/C

WIRING DIAGRAM


C107868E01


INSPECTION PROCEDURE

1.CHECK CAN BUS LINES FOR SHORT (DLC3 SUB BUS LINE)


    G031933E05
  1. Disconnect the DLC3 sub bus line connector (H5) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    G026206E24
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    H23-6 (CANH) -
    H23-14 (CANL)
    IG switch OFF
    1 MΩ or more



NG
REPAIR OR REPLACE DLC3 SUB BUS LINE OR CONNECTOR (CAN-H, CAN-L)
OK


2.CONNECT CONNECTOR
  1. Reconnect the DLC3 sub bus line connector (H5) to the CAN J/C.


NEXT


3.CHECK CAN BUS LINES FOR SHORT (AIR CONDITIONING AMPLIFIER SUB BUS LINE)


    G031933E06
  1. Disconnect the air conditioning amplifier sub bus line connector (H3) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    G026206E24
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    H23-6 (CANH) -
    H23-14 (CANL)
    IG switch OFF
    54 to 69 Ω



OK
Go to step 6
NG


4.CONNECT CONNECTOR
  1. Reconnect the air conditioning amplifier sub bus line connector (H3) to the CAN J/C.


NEXT


5.CHECK CAN BUS LINES FOR SHORT (ECM MAIN BUS LINE)


    G031933E04
  1. Disconnect the ECM main bus line connector (H4) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    G026206E24
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    H23-6 (CANH) -
    H23-14 (CANL)
    IG switch OFF
    108 to 132 Ω



OK
Go to step 8
NG

REPLACE CAN J/C 

6.CONNECT CONNECTOR
  1. Reconnect the air conditioning amplifier sub bus line connector (H3) to the CAN J/C.


NEXT


7.CHECK CAN BUS LINES FOR SHORT (AIR CONDITIONING AMPLIFIER SUB BUS LINE)


    C107863E04
  1. Disconnect the air conditioning amplifier connector (H18).



    G026206E24
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    H23-6 (CANH) -
    H23-14 (CANL)
    IG switch OFF
    54 to 69 Ω



OK
REPLACE AIR CONDITIONING AMPLIFIER
NG

REPAIR OR REPLACE AIR CONDITIONING AMPLIFIER SUB BUS LINE OR CONNECTOR (CAN-H, CAN-L) 

8.CONNECT CONNECTOR
  1. Reconnect the ECM main bus line connector (H4) to the CAN J/C.


NEXT


9.CHECK CAN BUS LINES FOR SHORT (ECM MAIN BUS LINE)


    C107867E04
  1. Disconnect the ECM connector (B7).



    G026206E24
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    H23-6 (CANH) -
    H23-14 (CANL)
    IG switch OFF
    108 to 132 Ω



OK
REPLACE ECM
NG

REPAIR OR REPLACE ECM MAIN BUS LINE OR CONNECTOR (CAN-H, CAN-L)