Home › BODY › INTERIOR › ROOF HEADLINING (for Full-trim)

ROOF HEADLINING (for Full-trim) > INSTALLATION

for Preparation Click here



1. INSTALL ROOF NO.1 HEADLINING (High Roof Type)


2. INSTALL ROOF NO.1 HEADLINING (Middle Roof Type)


3. INSTALL VISOR HOLDER


4. INSTALL VISOR ASSEMBLY LH


5. INSTALL VISOR ASSEMBLY RH


6. INSTALL REAR COOLER CONTROL PANEL (w/ Rear Cooler)


7. INSTALL MAP LIGHT ASSEMBLY (Super Wagon)


8. INSTALL ROOM LIGHT ASSEMBLY NO.1 (Deluxe)


9. INSTALL ASSIST GRIP


10. INSTALL FRONT PILLAR GARNISH RH


11. INSTALL FRONT PILLAR GARNISH LH


12. INSTALL ASSIST GRIP ASSEMBLY


13. INSTALL FRONT ASSIST GRIP PLUG NO.1


14. INSTALL ROOF NO.2 HEADLINING (High Roof Type)


15. INSTALL ROOF NO.2 HEADLINING (Middle Roof Type)


16. INSTALL ROOM LIGHT ASSEMBLY NO.2 (Super Wagon)


17. INSTALL ROOM LIGHT ASSEMBLY NO.2 (Deluxe)


18. INSTALL REAR SEAT HOOK (Space Up Seat)


19. INSTALL ROOF SIDE GARNISH INNER UPPER RH


20. INSTALL ROOF SIDE GARNISH INNER UPPER LH


21. INSTALL QUARTER PILLAR GARNISH RH (Middle Roof Type)


22. INSTALL QUARTER PILLAR GARNISH LH (Middle Roof Type)


23. INSTALL QUARTER PILLAR GARNISH RH (High Roof Type)


24. INSTALL QUARTER PILLAR GARNISH LH (High Roof Type)


25. INSTALL CENTER PILLAR GARNISH RH


26. INSTALL CENTER PILLAR GARNISH LOWER RH


27. INSTALL ASSIST GRIP ASSEMBLY REAR


28. INSTALL ASSIST GRIP PLUG


29. INSTALL CENTER PILLAR GARNISH LH


30. INSTALL ENGINE SERVICE HOLE COVER HOOK NO.2 LH


31. INSTALL SIDE NO.1 TRIM ASSEMBLY LH


32. INSTALL QUARTER TRIM PANEL ASSEMBLY REAR RH


33. INSTALL QUARTER TRIM PANEL ASSEMBLY REAR LH (High Roof Type)


34. INSTALL QUARTER TRIM PANEL ASSEMBLY REAR LH (Middle Roof Type)


35. INSTALL BACK DOOR WEATHERSTRIP


36. INSTALL BACK DOOR SCUFF PLATE


37. INSTALL SLIDE DOOR WEATHERSTRIP NO.1 RH


38. INSTALL REAR DOOR SCUFF PLATE RH


39. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH


    B103246
  1. Install the front seat outer belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B115749
  1. Engage the 2 claws to install the cover.



    B103256
  1. Install the front seat outer belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



40. INSTALL SEAT BELT ANCHOR COVER


41. INSTALL SEAT ASSEMBLY LH


42. INSTALL CENTER PILLAR GARNISH COVER LOWER LH


43. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH


    B101642
  1. Install the front seat outer belt assembly RH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B115750
  1. Engage the 2 claws to install the cover.



    B103254
  1. Install the front seat outer belt assembly RH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



44. INSTALL FRONT DOOR OPENING TRIM RH


45. INSTALL FRONT DOOR OPENING TRIM LH


46. INSTALL FRONT DOOR SCUFF PLATE RH


47. INSTALL FRONT DOOR SCUFF PLATE LH


48. INSTALL NO.4 SEAT BELT ASSEMBLY OUTER LH


    B107675
  1. Check the degree of tilt when the ELR begins to lock.

    1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

      NOTICE:
      Do not disassemble the retractor.



    B107674
  1. Install the No.4 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B107673
  1. Engage the 4 claws to install the retractor cover of the No.4 seat belt assembly outer.



    B107672
  1. Connect the shoulder side of the No.4 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B107671
  1. Engage the 2 claws to install the shoulder side cover of the No.4 seat belt assembly outer.



    B107670
  1. Connect the floor side of the No.4 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    This check should be performed with the outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
      If operation is not as specified, replace the outer belt assembly.



49. INSTALL NO.3 SEAT BELT ASSEMBLY OUTER LH


    B107669
  1. Check the degree of tilt when the ELR begins to lock.

    1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

      NOTICE:
      Do not disassemble the retractor.



    B107668
  1. Install the No.3 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B107667
  1. Engage the 4 claws to install the retractor cover of the No.3 seat belt assembly outer.



    B107666
  1. Connect the shoulder side of the No.3 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B107665
  1. Engage the 4 claws to install the retractor cover of the No.3 seat belt assembly outer.



    B107664
  1. Connect the floor side of the No.3 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    This check should be performed with the outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
      If operation is not as specified, replace the outer belt assembly.



50. INSTALL REAR NO.2 SEAT BELT ASSEMBLY OUTER LH


    B113927
  1. Check the degree of tilt when the ELR begins to lock.

    1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

      NOTICE:
      Do not disassemble the retractor.



    B105617
  1. Install the rear No.2 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B105616
  1. Connect the shoulder side of the rear No.2 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B105615
  1. Engage the 2 claws to install the retractor cover of the rear No.2 seat belt assembly outer.



    B105614
  1. Connect the floor side of the rear No.2 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    This check should be performed with the outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
      If operation is not as specified, replace the outer belt assembly.



51. INSTALL REAR SEAT BELT ASSEMBLY OUTER


    B107663
  1. Check the degree of tilt when the ELR begins to lock.

    1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

      NOTICE:
      Do not disassemble the retractor.



    B107662
  1. Install the rear seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B107661
  1. Connect the shoulder side of the rear seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B107660
  1. Engage the 4 claws to install the retractor cover of the rear seat belt assembly outer.



    B107659
  1. Connect the floor side of the rear seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    This check should be performed with the outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
      If operation is not as specified, replace the outer belt assembly.



52. INSTALL REAR NO. 4 SEAT ASSEMBLY


    B115899
  1. Secure the rear No.4 seat assembly with the 2 locks

  1. Install the rear No.4 seat assembly with the 3 bolts and 2 nuts.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

    NOTICE:
    After installing the rear No.4 seat assembly, fold down the seatback onto the seat cushion, lift the side of the rear No.4 seat assembly, and drop it to engage the locks securely.



53. INSTALL REAR NO. 3 SEAT ASSEMBLY


    B105606
  1. Install the rear No.3 seat assembly with the 6 bolts and 2 nuts.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }



54. INSTALL REAR NO. 2 SEAT ASSEMBLY


    B107603
  1. Install the rear No.2 seat assembly with the 4 bolts and 2 nuts.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

    HINT:
    1. Use the same procedure for the second row.
    2. Use the same procedure for the third row.



55. INSTALL REAR NO. 1 SEAT ASSEMBLY


    B107565
  1. Front row:

    1. Install the rear No.1 seat assembly with the 3 bolts and nut.

      Torque:
      39 N*m{ 398 kgf*cm , 29 ft.*lbf }



    B107566
  1. Second row:

    1. Install the rear No.1 seat assembly with the 2 bolts and 2 nuts.

      Torque:
      39 N*m{ 398 kgf*cm , 29 ft.*lbf }



56. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


57. PERFORM INITIALIZATION

HINT:
Some systems need initialization when disconnecting the cable from the negative battery terminal. (Click here)