ROOF HEADLINING (for Full-trim) > REMOVAL |
| 1. DISCONNECT BATTERY NEGATIVE CABLE |
| 2. REMOVE REAR NO. 1 SEAT ASSEMBLY |
![]() |
First row:
Remove the 3 bolts, nut and rear No.1 seat assembly.
![]() |
Second row:
Remove the 2 bolts, 2 nuts and rear No.1 seat assembly.
| 3. REMOVE REAR NO. 2 SEAT ASSEMBLY |
![]() |
Remove the 4 bolts, 2 nuts and rear No.2 seat assembly.
| 4. REMOVE REAR NO. 3 SEAT ASSEMBLY |
![]() |
Remove the 6 bolts, 2 nuts and rear No.3 seat assembly.
| 5. REMOVE REAR NO. 4 SEAT ASSEMBLY |
![]() |
Remove the 3 bolts and 2 nuts.
Pull the lever in the direction indicated by the arrow in the illustration, release the 2 locks, and remove the rear No.4 seat assembly.
| 6. REMOVE REAR SEAT BELT ASSEMBLY OUTER |
![]() |
Remove the bolt and disconnect the floor side of rear seat belt assembly outer.
![]() |
Using a screwdriver, disengage the 4 claws and disconnect the shoulder side cover of the rear seat belt assembly outer.
![]() |
Disconnect the bolt and shoulder side the rear seat belt assembly outer.
![]() |
Disconnect the bolt and remove the rear seat belt assembly outer.
| 7. REMOVE REAR NO.2 SEAT BELT ASSEMBLY OUTER LH |
![]() |
Remove the bolt and disconnect the floor side of the rear No.2 seat belt assembly outer.
![]() |
Using a screwdriver, disengage the 2 claws and disconnect the shoulder side cover of the rear No.2 seat belt assembly outer.
![]() |
Remove the bolt and disconnect the shoulder side of the rear No.2 seat belt assembly outer.
![]() |
Remove the bolt and remove the rear No.2 seat belt assembly outer.
| 8. REMOVE NO.3 SEAT BELT ASSEMBLY OUTER LH |
![]() |
Remove the bolt and disconnect the floor side of the rear No.3 seat belt assembly outer.
![]() |
Using a screwdriver, disengage the 4 claws and disconnect the shoulder side cover of the rear No.3 seat belt assembly outer.
![]() |
Disconnect the bolt and shoulder side of the rear No.3 seat belt assembly outer.
![]() |
Using a screwdriver, disengage the 4 claws and disconnect the rear No.3 seat belt assembly outer retractor cover.
![]() |
Remove the bolt and rear No.3 seat belt assembly outer.
| 9. REMOVE NO.4 SEAT BELT ASSEMBLY OUTER LH |
![]() |
Remove the bolt and disconnect the floor side of the rear No.4 seat belt assembly outer.
![]() |
Using a screwdriver, disengage the shoulder side cover of the 2 claws and disconnect the rear No.4 seat belt assembly outer.
![]() |
Remove the bolt and disconnect the shoulder side of the rear No.4 seat belt assembly outer.
![]() |
Using a screwdriver, disengage the 4 claws and disconnect the rear No.4 seat belt assembly outer retractor cover.
![]() |
Remove the bolt and rear No.4 seat belt assembly outer.
| 10. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Remove the 5 clips and front door scuff plate LH.
| 11. REMOVE FRONT DOOR SCUFF PLATE RH |
| 12. REMOVE FRONT DOOR OPENING TRIM LH |
| 13. REMOVE FRONT DOOR OPENING TRIM RH |
| 14. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH |
![]() |
Remove the bolt and disconnect front seat outer belt assembly RH.
![]() |
Using a screwdriver, disengage the 2 claws and cover.
![]() |
Remove the bolt and disconnect front seat outer belt assembly RH.
| 15. REMOVE CENTER PILLAR GARNISH COVER LOWER LH |
![]() |
Using a screwdriver, disengage the 4 clips and remove the center pillar garnish lower LH.
| 16. REMOVE SEAT ASSEMBLY LH |
Disconnect connector.
![]() |
Remove the nut and 3 bolts.
Remove the seat assembly LH.
| 17. REMOVE SEAT BELT ANCHOR COVER |
![]() |
Remove the 2 clips.
Disengage the claw and then remove the seat belt anchor cover.
| 18. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH |
![]() |
Remove the bolt and disconnect the front seat outer belt assembly LH.
![]() |
Using a screwdriver, disengage the 2 claws and cover.
![]() |
Remove the bolt and disconnect the front seat outer belt assembly LH.
| 19. REMOVE REAR DOOR SCUFF PLATE RH |
![]() |
Using a screwdriver, disengage the 11 clips and remove the rear door scuff plate LH.
| 20. REMOVE SLIDE DOOR WEATHERSTRIP NO.1 RH |
| 21. REMOVE BACK DOOR SCUFF PLATE |
![]() |
Using a screwdriver, disengage the 7 clips and 4 claws and remove the back door scuff plate.
| 22. REMOVE BACK DOOR WEATHERSTRIP |
| 23. REMOVE QUARTER TRIM PANEL ASSEMBLY REAR LH (Middle Roof Type) |
![]() |
Using a screwdriver, disengage the 21 clips and remove the quarter trim panel assembly rear LH.
| 24. REMOVE QUARTER TRIM PANEL ASSEMBLY REAR LH (High Roof Type) |
![]() |
Using a screwdriver, disengage the 35 clips and remove the quarter trim panel assembly rear LH.
| 25. REMOVE QUARTER TRIM PANEL ASSEMBLY REAR RH |
| 26. REMOVE SIDE NO.1 TRIM ASSEMBLY LH |
![]() |
Using a screwdriver, disengage the 21 clips and remove the side No.1 trim assembly LH.
| 27. REMOVE ENGINE SERVICE HOLE COVER HOOK NO.2 LH |
![]() |
Remove the screw and engine service hole cover hook No.2 LH.
| 28. REMOVE CENTER PILLAR GARNISH LH |
![]() |
Using a screwdriver, disengage the 5 clips and 2 claws, and remove the center pillar garnish LH.
| 29. REMOVE ASSIST GRIP PLUG |
![]() |
Using a screwdriver, disengage the assist grip plugs.
| 30. REMOVE ASSIST GRIP ASSEMBLY REAR |
![]() |
Remove the 2 screws and assist grip assembly rear.
| 31. REMOVE CENTER PILLAR GARNISH LOWER RH |
![]() |
Release the 4 claws and remove the center pillar garnish lower RH.
| 32. REMOVE CENTER PILLAR GARNISH RH |
![]() |
Release the 3 clips, claw and remove the center pillar garnish RH.
| 33. REMOVE QUARTER PILLAR GARNISH LH (High Roof Type) |
![]() |
Release the 6 clips and remove the quarter pillar garnish LH.
| 34. REMOVE QUARTER PILLAR GARNISH RH (High Roof Type) |
| 35. REMOVE QUARTER PILLAR GARNISH LH (Middle Roof Type) |
![]() |
Release the 3clips and remove the quarter pillar garnish LH.
| 36. REMOVE QUARTER PILLAR GARNISH RH (Middle Roof Type) |
| 37. REMOVE ROOF SIDE GARNISH INNER UPPER LH |
![]() |
Using a screwdriver, disengage the 6 clips and remove the roof side garnish inner upper LH.
| 38. REMOVE ROOF SIDE GARNISH INNER UPPER RH |
| 39. REMOVE REAR SEAT HOOK (Space Up Seat) |
![]() |
Remove the bolt and rear seat hook.
| 40. REMOVE ROOM LIGHT ASSEMBLY NO.2 (Deluxe) |
![]() |
Using a screwdriver, disengage the 4 claws and remove the room light lens cover.
![]() |
Remove the 2 screws.
Disconnect the connector and remove the room light assembly No.2.
| 41. REMOVE ROOM LIGHT ASSEMBLY NO.2 (Super Wagon) |
![]() |
Using a screwdriver, disengage the claw and remove the room light base.
Remove the 2 screws.
![]() |
Pull the room light assembly No.2 rearward and disengage the claw.
Release the connector and remove the room light assembly No.2.
| 42. REMOVE ROOF HEADLINING NO.2 (Middle Roof Type) |
![]() |
Using a clip remover, disengage the 20 clips and remove the roof headlining No.2.
| 43. REMOVE ROOF HEADLINING NO.2 (High Roof Type) |
![]() |
Using a clip remover, disengage the 26 clips and remove the roof headlining No.2.
| 44. REMOVE FRONT ASSIST GRIP PLUG NO.1 |
![]() |
Using a screwdriver, disengage the assist grip plug No.1.
| 45. REMOVE ASSIST GRIP ASSEMBLY |
![]() |
Remove the 2 screws and assist grip.
| 46. REMOVE FRONT PILLAR GARNISH LH |
![]() |
Using a screwdriver, disengage the clip and claw and remove the front pillar garnish LH.
| 47. REMOVE FRONT PILLAR GARNISH RH |
| 48. REMOVE ASSIST GRIP |
![]() |
Using a screwdriver, disengage the assist grip plugs.
![]() |
Remove the 2 screws and assist grip.
| 49. REMOVE VISOR HOLDER |
![]() |
Remove the screw.
Using a moulding remover, disengage the claw and remove the visor holder.
| 50. REMOVE VISOR ASSEMBLY LH |
![]() |
Remove the 2 screws and visor assembly LH.
| 51. REMOVE VISOR ASSEMBLY RH |
| 52. REMOVE ROOM LIGHT ASSEMBLY NO.1 (Deluxe) |
![]() |
Using a screwdriver, disengage the 4 claws and remove the room light lens cover.
![]() |
Remove the 2 screws.
Disconnect the connector and remove the room light assembly No.1.
| 53. REMOVE MAP LIGHT ASSEMBLY (Super Wagon) |
![]() |
Using a moulding remover, disengage the 4 claws and map light assembly.
Disconnect the connector and remove the map light assembly.
| 54. REMOVE REAR COOLER CONTROL PANEL (w/Rear Cooler) |
| 55. REMOVE ROOF HEADLINING NO.1 (Middle Roof Type) |
![]() |
w/ Rear Cooler:
Remove the 4 screws.
Using a clip remover, disengage the 9 clips and remove the roof headlining No.1.
| 56. REMOVE ROOF HEADLINING NO.1 (High Roof Type) |
![]() |
w/ Rear Cooler:
Remove the 4 screws.
Using a clip remover, disengage the 15 clips and remove the roof headlining No.1.