Home › BODY ELECTRICAL › AUDIO / VISUAL › ROOF SPEAKER

ROOF SPEAKER > REMOVAL

for Preparation Click here



1. DISCONNECT BATTERY NEGATIVE CABLE
(Click here)


2. REMOVE REAR NO. 1 SEAT ASSEMBLY


    B107585
  1. First row:

    1. Remove the 3 bolts, nut and rear No.1 seat assembly.



    B107586
  1. Second row:

    1. Remove the 2 bolts, 2 nuts and rear No.1 seat assembly.



3. REMOVE REAR NO. 2 SEAT ASSEMBLY


    B107603
  1. Remove the 4 bolts, 2 nuts and rear No.2 seat assembly.

    HINT:
    1. Use the same procedure for the second row.
    2. Use the same procedure for the third row.



4. REMOVE REAR NO. 3 SEAT ASSEMBLY


    B105606
  1. Remove the 6 bolts, 2 nuts and rear No.3 seat assembly.



5. REMOVE REAR NO. 4 SEAT ASSEMBLY


    B107625
  1. Remove the 3 bolts and 2 nuts.

  1. Pull the lever in the direction indicated by the arrow in the illustration, release the 2 locks, and remove the rear No.4 seat assembly.



6. REMOVE REAR SEAT BELT ASSEMBLY OUTER


    B107659
  1. Remove the bolt and disconnect the floor side of rear seat belt assembly outer.



    B107660
  1. Using a screwdriver, disengage the 4 claws and disconnect the shoulder side cover of the rear seat belt assembly outer.

    HINT:
    Tape the screwdriver tip before use.



    B107661
  1. Disconnect the bolt and shoulder side the rear seat belt assembly outer.



    B107662
  1. Disconnect the bolt and remove the rear seat belt assembly outer.



7. REMOVE REAR NO.2 SEAT BELT ASSEMBLY OUTER LH


    B105614
  1. Remove the bolt and disconnect the floor side of the rear No.2 seat belt assembly outer.



    B105615
  1. Using a screwdriver, disengage the 2 claws and disconnect the shoulder side cover of the rear No.2 seat belt assembly outer.

    HINT:
    Tape the screwdriver tip before use.



    B105616
  1. Remove the bolt and disconnect the shoulder side of the rear No.2 seat belt assembly outer.



    B105617
  1. Remove the bolt and remove the rear No.2 seat belt assembly outer.



8. REMOVE NO.3 SEAT BELT ASSEMBLY OUTER LH


    B107664
  1. Remove the bolt and disconnect the floor side of the rear No.3 seat belt assembly outer.



    B107665
  1. Using a screwdriver, disengage the 4 claws and disconnect the shoulder side cover of the rear No.3 seat belt assembly outer.

    HINT:
    Tape the screwdriver tip before use.



    B107666
  1. Disconnect the bolt and shoulder side of the rear No.3 seat belt assembly outer.



    B107667
  1. Using a screwdriver, disengage the 4 claws and disconnect the rear No.3 seat belt assembly outer retractor cover.



    B107668
  1. Remove the bolt and rear No.3 seat belt assembly outer.



9. REMOVE NO.4 SEAT BELT ASSEMBLY OUTER LH


    B107664
  1. Remove the bolt and disconnect the floor side of the rear No.3 seat belt assembly outer.



    B107665
  1. Using a screwdriver, disengage the 4 claws and disconnect the shoulder side cover of the rear No.3 seat belt assembly outer.

    HINT:
    Tape the screwdriver tip before use.



    B107666
  1. Disconnect the bolt and shoulder side of the rear No.3 seat belt assembly outer.



    B107667
  1. Using a screwdriver, disengage the 4 claws and disconnect the rear No.3 seat belt assembly outer retractor cover.



    B107668
  1. Remove the bolt and rear No.3 seat belt assembly outer.



10. REMOVE FRONT DOOR SCUFF PLATE LH


    B115746
  1. Remove the 5 clips and front door scuff plate LH.



11. REMOVE FRONT DOOR SCUFF PLATE RH


12. REMOVE FRONT DOOR OPENING TRIM LH


13. REMOVE FRONT DOOR OPENING TRIM RH


14. REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH


    B103254
  1. Remove the bolt and disconnect the floor side of the front seat outer belt assembly RH.



15. REMOVE CENTER PILLAR GARNISH COVER LOWER LH


    B106182E01
  1. Using a screwdriver, disengage the 4 clips and remove the center pillar garnish lower LH.



16. REMOVE SEAT ASSEMBLY


    B107542
  1. Move the front seat assembly fully forward.

  1. Remove the 2 bolts on the rear side of the seat.

  1. Move the front seat assembly to the rearmost position.

  1. Remove the 2 bolts on the front side of the seat.

  1. Move the front seat assembly to the center of the seat slide rail. Set the seatback in the upright position.

  1. Disconnect the front seat inner belt assembly connector.

  1. Remove the front seat assembly.



17. REMOVE SEAT BELT ANCHOR COVER


    B103255E01
  1. Remove the 2 clips.

  1. Disengage the claw and then remove the seat belt anchor cover.



18. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH


    B103254
  1. Remove the bolt and disconnect the floor side of the front seat outer belt assembly RH.



19. REMOVE REAR DOOR SCUFF PLATE RH


    B113347
  1. Using a screwdriver, disengage the 11 clips and remove the rear door scuff plate LH.

    HINT:
    Tape the screwdriver tip before use.



20. REMOVE SLIDE DOOR WEATHERSTRIP NO.1 RH


21. REMOVE BACK DOOR SCUFF PLATE


    B106176E01
  1. Using a screwdriver, disengage the 7 clips and 4 claws and remove the back door scuff plate.

    HINT:
    Tape the screwdriver tip before use.



22. REMOVE BACK DOOR WEATHERSTRIP


23. REMOVE QUARTER TRIM PANEL ASSEMBLY REAR LH


    B113348
  1. Using a screwdriver, disengage the 35 clips and remove the quarter trim panel assembly rear LH.

    HINT:
    Tape the screwdriver tip before use.



24. REMOVE QUARTER TRIM PANEL ASSEMBLY REAR RH


25. REMOVE SIDE NO.1 TRIM ASSEMBLY LH


26. REMOVE ENGINE SERVICE HOLE COVER HOOK NO.2 LH


    B112983
  1. Remove the screw and engine service hole cover hook No.2 LH.



27. REMOVE CENTER PILLAR GARNISH LH


    B113350
  1. Using a screwdriver, disengage the 5 clips and 2 claws, and remove the center pillar garnish LH.

    HINT:
    Tape the screwdriver tip before use.



28. REMOVE ASSIST GRIP PLUG


    B113268
  1. Using a screwdriver, disengage the assist grip plugs.

    HINT:
    Tape the screwdriver tip before use.



29. REMOVE ASSIST GRIP ASSEMBLY REAR


    B113269
  1. Remove the 2 screws and assist grip assembly rear.



30. REMOVE CENTER PILLAR GARNISH LOWER RH


    B113351
  1. Release the 3 clips, claw and remove the center pillar garnish RH.



31. REMOVE CENTER PILLAR GARNISH RH


    B113012
  1. Release the 4 claws and remove the center pillar garnish lower RH.



32. REMOVE QUARTER PILLAR GARNISH LH


    B106184E02
  1. Release the 6 clips and remove the quarter pillar garnish LH.



33. REMOVE QUARTER PILLAR GARNISH RH


34. REMOVE ROOF SIDE GARNISH INNER UPPER LH


    B113352
  1. Using a screwdriver, disengage the 6 clips and remove the roof side garnish inner upper LH.

    HINT:
    Tape the screwdriver tip before use.



35. REMOVE ROOF SIDE GARNISH INNER UPPER RH


36. REMOVE REAR SEAT HOOK


    B113353
  1. Remove the bolt and rear seat hook.



37. REMOVE ROOM LIGHT ASSEMBLY NO.2


    B113362
  1. Using a screwdriver, disengage the claw and remove the room light base.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the 2 screws.



    B113363E01
  1. Pull the room light assembly No.2 rearward and disengage the claw.

  1. Release the connector and remove the room light assembly No.2.



38. REMOVE ROOF NO.2 HEADLINING


    B110051E01
  1. Using a clip remover, disengage the 26 clips and remove the roof headlining No.2.

    HINT:
    The clips in the illustration are part of the components. Remove them together with the roof headlining No.2.



39. REMOVE FRONT ASSIST GRIP PLUG NO.1 RH


40. REMOVE ASSIST GRIP ASSEMBLY REAR


41. REMOVE FRONT PILLAR GARNISH LH


42. REMOVE FRONT PILLAR GARNISH RH


43. REMOVE ASSIST GRIP


44. REMOVE VISOR HOLDER


45. REMOVE LH VISOR ASSEMBLY


46. REMOVE RH VISOR ASSEMBLY


47. REMOVE ROOM LIGHT ASSY


48. REMOVE MAP LIGHT ASSEMBLY


49. REMOVE REAR COOLER CONTROL PANEL


    E108775E01
  1. Release the 4 clips and 4 claws, and disconnect the rear cooler control panel.

  1. Disconnect the connector and remove the rear cooler control panel.



50. REMOVE ROOF NO.1 HEADLINING


    B112985E02
  1. w/ Rear Cooler:
    Remove the 4 screws.

  1. Using a clip remover, disengage the 15 clips and remove the roof headlining No.1.

    HINT:
    The clips in the illustration are part of the components. Remove them together with the roof headlining No.1.



51. REMOVE ROOF SPEAKER


    E106401
  1. Disconnect the connector.

  1. Remove the 2 bolts and the roof speaker assembly.