Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM (w/o Secondary Air Injection System)

SFI SYSTEM (w/o Secondary Air Injection System) > ECM Power Source Circuit

for Preparation Click here


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to terminal IGSW of the ECM. The ECM MREL output signal causes a current to flow to the coil, closing the contacts of the integration relay (MAIN relay) and supplying power to terminal +B of the ECM.

WIRING DIAGRAM


A111675E01


INSPECTION PROCEDURE

1.INSPECT ECM (+B VOLTAGE)


    A018294E28
  1. Turn the ignition switch to the ON position.

  1. Measure the voltage between the terminals of the ECM connectors.

    Voltage:
    Tester Connections
    Specified Conditions
    +B (B9-1) - E1 (D1-3)
    9 to 14 V



OK
GO TO PROBLEM SYMPTOMS TABLE
NG


2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)


    A065743E20
  1. Disconnect the negative battery cable.

  1. Disconnect the D1 ECM connector.

  1. Measure the resistance.

    Resistance (Check for open):
    Tester Connections
    Specified Conditions
    E1 (D1-3) - Body ground
    Below 1 Ω

  1. Reconnect the ECM connector.

  1. Reconnect the negative battery cable.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT ECM (IGSW VOLTAGE)


    A018294E29
  1. Turn the ignition switch to the ON position.

  1. Measure the voltage between the terminals of the ECM connectors.

    Voltage:
    Tester Connections
    Specified Conditions
    IGSW (B9-9) - E1 (D1-3)
    9 to 14 V



OK
Go to step 6
NG


4.CHECK AM2 OR IGN FUSE


    A111557E01
  1. Check the AM2 fuse.

    1. Remove the AM2 fuse from the engine room R/B No.2.

    2. Measure the AM2 fuse resistance.

      Resistance:
      Below 1 Ω

    3. Reinstall the AM2 fuse.

  1. Check the IGN fuse.

    1. Remove the IGN fuse from the instrument panel J/B.

    2. Measure the IGN fuse resistance.

      Resistance:
      Below 1 Ω

    3. Reinstall the IGN fuse.



NG
REPLACE AM2 OR IGN FUSE
OK


5.INSPECT IGNITION SWITCH


    G037118E01
  1. Disconnect the I7 ignition switch connector.

  1. Measure the resistance.

    Resistance:
    Ignition Switch Positions
    Tester Connections
    Specified Conditions
    LOCK
    All Terminals
    10 kΩ or higher
    ACC
    2 - 3
    Below 1 Ω
    ON
    2 - 3, 2 - 4, 6 - 7
    Below 1 Ω
    START
    2 - 3, 6 - 7, 1 - 2, 7 - 8
    Below 1 Ω

  1. Reconnect the ignition switch connector.



NG
REPLACE IGNITION SWITCH
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH, IGNITION SWITCH - ECM) 

6.INSPECT ECM (MREL VOLTAGE)


    A018294E30
  1. Turn the ignition switch to the ON position.

  1. Measure the voltage between the terminals of the ECM connectors.

    Voltage:
    Tester Connector
    Specified Condition
    MREL (B9-8) - E1 (D1-3)
    9 to 14 V



NG
REPLACE ECM
OK


7.CHECK EFI FUSE


    A102921E01
  1. Remove the EFI fuse from the engine room R/B No.1.

  1. Measure the EFI fuse resistance.

    Resistance:
    Below 1 Ω

  1. Reinstall the EFI fuse.



NG
REPLACE EFI FUSE
OK


8.INSPECT INTEGRATION RELAY (EFI RELAY)
  1. Remove the integration relay from the engine room R/B No.1.



    A095606E01
  1. Measure the integration relay (MAIN relay) resistance.

    Resistance:
    Tester Connections
    Specified Conditions
    A1 - B4
    10 kΩ or higher
    A1 - B4
    Below 1 Ω
    (when battery voltage applied to terminals B2 and B3)

  1. Reinstall the integration relay.



NG
REPLACE INTEGRATION RELAY
OK


9.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM, INTEGRATION RELAY - BODY GROUND)


    A111558E01
  1. Check the harness and connector between the integration relay and the ECM.

    1. Remove the Integration relay from the engine room R/B No.1.

    2. Disconnect the B9 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Resistance (Check for open):
      Tester Connection
      Specified Condition
      Integration relay (B2) - MREL (B9-8)
      Below 1 Ω

      Resistance (Check for short):
      Tester Connection
      Specified Condition
      Integration relay (B2) or MREL (B9-8)
      - Body ground
      10 kΩ or higher

  1. Check the harness and connector between the integration relay and the body ground.

    1. Remove the integration relay from the engine room R/B No.1.

    2. Measure the resistance according to the value(s) in the table below.

      Resistance (Check for open):
      Tester Connection
      Specified Condition
      Integration relay (B3) - Body ground
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY - BATTERY POSITIVE TERMINAL)