DTC P0120/41 Throttle Pedal Position Sensor / Switch "A" Circuit Malfunction |
DTC P0122/41 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input |
DTC P0123/41 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input |
DTC P0220/41 Throttle / Pedal Position Sensor / Switch "B" Circuit |
DTC P0222/41 Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input |
DTC P0223/41 Throttle / Pedal Position Sensor / Switch "B" Circuit High Input |
DTC P2135/41 Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation |

| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0120/41 | Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds (1 trip detection logic) |
|
| P0122/41 | Output voltage of VTA1 0.2 V or less for 2 seconds (1 trip detection logic) |
|
| P0123/41 | Output voltage of VTA1 4.8 V or more for 2 seconds (1 trip detection logic) |
|
| P0220/41 | Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds (1 trip detection logic) |
|
| P0222/41 | Output voltage of VTA2 0.5 V or less for 2 seconds (1 trip detection logic) |
|
| P0223/41 | Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 1.8 V, for 2 seconds (1 trip detection logic) |
|
| P2135/41 |
|
|
| Tester Display | Accelerator Pedal Fully Released | Accelerator Pedal Fully Depressed |
| Throttle Pos #1 | Between 10 % and 22 % | Between 60% and 99 % |
| Throttle Pos #2 | Between 2.1 V and 3.1 V | Between 4.5 V and 5.0 V |

| 1.READ VALUE OF INTELLIGENT TESTER (THROTTLE POS #1 AND THROTTLE POS #2) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the intelligent tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Throttle Pos #1 and Throttle Pos #2.
Check the values displayed on the tester.
| TP#1 (VTA1) When AP Released | TP#2 (VTA2) When AP Released | TP#1 (VTA1) When AP Depressed | TP#2 (VTA2) When AP Depressed | Trouble Areas | Proceed To |
| 0 % | Between 0 V and 0.2 V | 0 % | Between 0 V and 0.2 V | VC circuit open | A |
| 100 % | Between 4.5 V and 5.0 V | 100 % | Between 4.5 V and 5.0 V | E2 circuit open | A |
| 0 % or 100 % | Between 2.1 V and 3.1 V (Fail-safe) | 0 % or 100 % | Between 2.1 V and 3.1 V (Fail-safe) | VTA1 circuit open or ground short | A |
| Approx 19 % (Fail-safe) | Between 0 V and 0.2 V, or 4.5 V and 5.0 V | Approx 19 % (Fail-safe) | Between 0 V and 0.2 V, or 4.5 V and 5.0 V | VTA2 circuit open or ground short | A |
| Between 10 % and 22 % | Between 2.1 V and 3.1 V | Between 66 % and 98 % (Not fail-safe) | Between 4.5 V and 5.0 V (Not fail-safe) | TP sensor circuit normal | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM) |
![]() |
Disconnect the D29 throttle body connector.
Disconnect the D1 ECM connector.
Measure the resistance.
| Tester Connections | Specified Conditions |
| VC (D29-5) - VC (D1-18) | Below 1 Ω |
| VTA (D29-6) - VTA1 (D1-20) | Below 1 Ω |
| VTA2 (D29-4) - VTA2 (D1-19) | Below 1 Ω |
| E2 (D29-3) - E2 (D1-28) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| VC (D29-5) or VC (D1-18) - Body ground | 10 kΩ or higher |
| VTA (D29-6) or VTA1 (D1-20) - Body ground | 10 kΩ or higher |
| VTA2 (D29-4) or VTA2 (D1-19) - Body ground | 10 kΩ or higher |
Reconnect the throttle body connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.INSPECT ECM (VC VOLTAGE) |
![]() |
Disconnect the D29 throttle body connector.
Turn the ignition switch to the ON position.
Measure the voltage between the terminals of the ECM connector.
| Tester Connections | Specified Conditions |
| VC (D1-18) - E2 (D1-28) | 4.5 to 5.5 V |
Reconnect the throttle body connector.
|
| ||||
| OK | |
| 4.REPLACE THROTTLE W/MOTOR BODY ASSEMBLY |
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester ON.
Clear DTCs (See page ).
Start the engine.
Allow the engine to idle for 15 seconds or more.
Read DTCs.
| Display (DTC Output) | Proceed To |
| P0120, P0122, P0123, P0220, P0222, P0223 and/or P2135 | A |
| No output | B |
|
| ||||
| A | ||
| ||