DTC P0115/22 Engine Coolant Temperature Circuit |
DTC P0117/22 Engine Coolant Temperature Circuit Low Input |
DTC P0118/22 Engine Coolant Temperature Circuit High Input |
| DTC No. | Proceed To | DTC Detection Conditions | Trouble Areas |
| P0115/22 | Step 1 | Open or short in Engine Coolant Temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| P0117/22 | Step 4 | Short in Engine Coolant Temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| P0118/22 | Step 2 | Open in Engine Coolant Temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| Temperature Displayed | Malfunctions |
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) or higher | Short circuit |

| 1.READ VALUE OF INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the value displayed on the tester.
| Temperature Displayed | Proceed To |
| -40°C (-40°F) | A |
| 140°C (284°F) or higher | B |
| Between 80°C and 97°C (176°F and 207°F) | C |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE OF INTELLIGENT TESTER (CHECK FOR OPEN IN HARNESS) |
Confirm good connection to the sensor.
![]() |
Disconnect the D32 Engine Coolant Temperature (ECT) sensor connector.
Connect terminals 1 and 2 of the ECT sensor connector on the wire harness side.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the value displayed on the tester.
Reconnect the ECT sensor connector.
|
| ||||
| NG | |
| 3.READ VALUE OF INTELLIGENT TESTER (CHECK FOR OPEN IN ECM) |
Confirm good connection to the ECM.
![]() |
Disconnect the D32 ECT sensor connector.
Connect terminals THW and E2 of the ECM connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the value displayed on the tester.
Reconnect the ECT sensor connector.
|
| ||||
| NG | ||
| ||
| 4.READ VALUE OF INTELLIGENT TESTER (CHECK FOR SHORT IN HARNESS) |
![]() |
Disconnect the D32 ECT sensor connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the value displayed on the tester.
Reconnect the ECT sensor connector.
|
| ||||
| NG | |
| 5.READ VALUE OF INTELLIGENT TESTER (CHECK FOR SHORT IN ECM) |
![]() |
Disconnect the D1 ECM connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the value displayed on the tester.
Reconnect the ECT sensor connector.
|
| ||||
| NG | ||
| ||