Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM (w/o Secondary Air Injection System)

DTC    P0351/14    Ignition Coil "A" Primary / Secondary Circuit

DTC    P0352/15    Ignition Coil "B" Primary / Secondary Circuit

DTC    P0353/14    Ignition Coil "C" Primary / Secondary Circuit

DTC    P0354/15    Ignition Coil "D" Primary / Secondary Circuit

for Preparation Click here


DESCRIPTION

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is set, check the No.1 ignition coil with igniter circuit.
  3. If DTC P0352 is set, check the No.2 ignition coil with igniter circuit.
  4. If DTC P0353 is set, check the No.3 ignition coil with igniter circuit.
  5. If DTC P0354 is set, check the No.4 ignition coil with igniter circuit.

A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrodes to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM, for each cylinder ignition.

A085099E01


DTC No.
DTC Detection Conditions
Trouble Areas
P0351/14
P0352/15
P0353/14
P0354/15
No IGF signal to ECM while engine running
(1 trip detection logic)
  1. Ignition system
  2. Open or short in IGF1 or IGT circuit (1 to 4) between ignition coil with igniter and ECM
  3. No.1 to No.4 ignition coils with igniters
  4. ECM
  1. Reference: Inspection using an oscilloscope
    While cranking or idling, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.
    A063956E02
    Items
    Contents
    Terminals
    CH1: IGT1, IGT2, IGT3, IGT4 - E1
    CH:2 IGF1 - E1
    Equipment Settings
    2 V/Division, 20 ms/Division
    Conditions
    Cranking or idling

MONITOR DESCRIPTION


A082388E08

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and sets a DTC.
If the malfunction is not repaired successfully, a DTC is set 1second after the engine is next started.

WIRING DIAGRAM


A111664E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351/14, P0352/15, P0353/14 OR P0354/15)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the tester ON.

  1. Clear DTCs (Click here).

  1. Shuffle the ignition coils with igniters (among No.1 to No.4 cylinders).

    NOTICE:
    Do not shuffle the connectors.

  1. Perform a simulation test.

  1. Check DTCs displayed on the tester.

    Result:

    Display (DTC Output)
    Proceed To
    Same DTC output
    A
    Other ignition coil DTC output
    B



B
REPLACE IGNITION COIL ASSEMBLY
A


2.INSPECT ECM (IGT1, IGT2, IGT3, IGT4 AND IGF1 SIGNAL)


    A110123E01
  1. Inspect the ECM using an oscilloscope.

  1. While cranking or idling, check the waveform between the terminals of the D1 ECM connector.

    Standard:
    Tester Connections
    Specified Conditions
    IGT1 (D1-17) - E1 (D1-3)
    Correct waveform shown in the illustration appears
    IGT2 (D1-16) - E1 (D1-3)
    Correct waveform shown in the illustration appears
    IGT3 (D1-15) - E1 (D1-3)
    Correct waveform shown in the illustration appears
    IGT4 (D1-14) - E1 (D1-3)
    Correct waveform shown in the illustration appears
    IGF1 (D1-23) - E1 (D1-3)
    Correct waveform shown in the illustration appears



NG
REPLACE ECM
OK


3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)


    A110126E01
  1. Disconnect the ignition coil with igniter connector.

  1. Disconnect the D1 ECM connector.

  1. Measure the resistance.

    Resistance (Check for open):
    Tester Connections
    Specified Conditions
    IGF (D20-2) - IGF1 (D1-23)
    Below 1 Ω
    IGF (D21-2) - IGF1 (D1-23)
    Below 1 Ω
    IGF (D22-2) - IGF1 (D1-23)
    Below 1 Ω
    IGF (D23-2) - IGF1 (D1-23)
    Below 1 Ω

    Resistance (Check for open):
    Tester Connections
    Specified Conditions
    IGT1 (D20-3) - IGT1 (D1-17)
    Below 1 Ω
    IGT2 (D21-3) - IGT2 (D1-16)
    Below 1 Ω
    IGT3 (D22-3) - IGT3 (D1-15)
    Below 1 Ω
    IGT4 (D23-3) - IGT4 (D1-14)
    Below 1 Ω

    Resistance (Check for short):
    Tester Connections
    Specified Conditions
    IGF (D20-2) or IGF1 (D1-23) - Body ground
    10 kΩ or higher
    IGF (D21-2) or IGF1 (D1-23) - Body ground
    10 kΩ or higher
    IGF (D22-2) or IGF1 (D1-23) - Body ground
    10 kΩ or higher
    IGF (D23-2) or IGF1 (D1-23) - Body ground
    10 kΩ or higher

    Resistance (Check for short):
    Tester Connections
    Specified Conditions
    IGT1 (D20-3) or IGT1 (D1-17) - Body ground
    10 kΩ or higher
    IGT2 (D21-3) or IGT2 (D1-16) - Body ground
    10 kΩ or higher
    IGT3 (D22-3) or IGT3 (D1-15) - Body ground
    10 kΩ or higher
    IGT4 (D23-3) or IGT4 (D1-14) - Body ground
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the ignition coil with igniter connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)


    A110444E01
  1. Disconnect the ignition coil with igniter connector.

  1. Measure the resistance.

    Resistance (Check for open):
    Tester Connections
    Specified Conditions
    GND (D20-4) - Body ground
    Below 1 Ω
    GND (D21-4) - Body ground
    Below 1 Ω
    GND (D22-4) - Body ground
    Below 1 Ω
    GND (D23-4) - Body ground
    Below 1 Ω

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage between the terminals of the wire harness side connector.

    Voltage:
    Tester Connections
    Specified Conditions
    +B (D20-1) - GND (D20-4)
    9 to 14 V
    +B (D21-1) - GND (D21-4)
    9 to 14 V
    +B (D22-1) - GND (D22-4)
    9 to 14 V
    +B (D23-1) - GND (D23-4)
    9 to 14 V

  1. Reconnect the ignition coil with igniter connector.



NG
Go to step 5
OK

REPLACE IGNITION COIL ASSEMBLY 

5.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - IGNITION SWITCH)


    A110127E01
  1. Disconnect the ignition coil with igniter connector.

  1. Disconnect the H25 ignition switch connector.

  1. Measure the resistance.

    Resistance (Check for open):
    Tester Connections
    Specified Conditions
    +B (D20-1) - IG2 (H25-6)
    Below 1 Ω
    +B (D21-1) - IG2 (H25-6)
    Below 1 Ω
    +B (D22-1) - IG2 (H25-6)
    Below 1 Ω
    +B (D23-1) - IG2 (H25-6)
    Below 1 Ω

    Resistance (Check for short):
    Tester Connections
    Specified Conditions
    +B (D20-1) or IG2 (H25-6) - Body ground
    10 kΩ or higher
    +B (D21-1) or IG2 (H25-6) - Body ground
    10 kΩ or higher
    +B (D22-1) or IG2 (H25-6) - Body ground
    10 kΩ or higher
    +B (D23-1) or IG2 (H25-6) - Body ground
    10 kΩ or higher

  1. Reconnect the ignition coil with igniter connector.

  1. Reconnect the ignition switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE IGNITION COIL ASSEMBLY