DTC P2120/19 Throttle / Pedal Position Sensor / Switch "D" Circuit |
DTC P2122/19 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input |
DTC P2123/19 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input |
DTC P2125/19 Throttle / Pedal Position Sensor / Switch "E" Circuit |
DTC P2127/19 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input |
DTC P2128/19 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input |
DTC P2138/19 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation |

| DTC No. | DTC Detection Conditions | Trouble Areas |
| P2120/19 | VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) |
|
| P2122/19 | VPA 0.2 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic) |
|
| P2123/19 | VPA 4.8 V or more for 2.0 seconds or more (1 trip detection logic) |
|
| P2125/19 | VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) |
|
| P2127/19 | VPA2 0.5 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic) |
|
| P2128/19 |
|
|
| P2138/19 |
|
|
| Trouble Areas | ACCEL POS #1 When AP Released | ACCEL POS #2 When AP Released | ACCEL POS #1 When AP Depressed | ACCEL POS #2 When AP Depressed |
| VCP circuit open | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V |
| Open or ground short in VPA circuit | 0 to 0.2 V | 1.2 to 2.0 V | 0 to 0.2 V | 3.4 to 5.0 V |
| Open or ground short in VPA2 circuit | 0.5 to 1.1 V | 0 to 0.2 V | 2.6 to 4.5 V | 0 to 0.2 V |
| EPA circuit open | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V |
| Normal condition | 0.5 to 1.1 V | 1.2 to 2.0 V | 2.6 to 4.5 V | 3.4 to 5.0 V |

| 1.READ VALUE OF INTELLIGENT TESTER (ACCEL POS #1 AND ACCEL POS #2) |
![]() |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Accel Pos #1 and Accel Pos #2.
Read the values displayed on the tester.
| Accelerator Pedal Operations | ACCEL POS #1 (AP #1) | ACCEL POS #2 (AP #2) |
| Released | 0.5 to 1.1 V | 1.2 to 2.0 V |
| Depressed | 2.6 to 4.5 V | 3.4 to 5.0 V |
|
| ||||
| NG | |
| 2.CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL POSITION SENSOR) |
![]() |
Disconnect the B1 Accelerator Pedal Position (APP) sensor connector.
Disconnect the B9 ECM connector.
Measure the resistance.
| Tester Connections | Specified Conditions |
| VPA (B1-6) - VPA (B9-18) | Below 1 Ω |
| EPA (B1-5) - EPA (B9-20) | Below 1 Ω |
| VCPA (B1-4) - VCPA (B9-26) | Below 1 Ω |
| VPA2 (B1-3) - VPA2 (B9-19) | Below 1 Ω |
| EPA2 (B1-2) - EPA2 (B9-21) | Below 1 Ω |
| VCP2 (B1-1) - VCP2 (B9-27) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| VPA (B1-6) or VPA (B9-18) - Body ground | 10 kΩ or higher |
| EPA (B1-5) or EPA (B9-20) - Body ground | 10 kΩ or higher |
| VCPA (B1-4) or VCPA (B9-26) - Body ground | 10 kΩ or higher |
| VPA2 (B1-3) or VPA2 (B9-19) - Body ground | 10 kΩ or higher |
| EPA2 (B1-2) or EPA2 (B9-21) - Body ground | 10 kΩ or higher |
| VCP2 (B1-1) or VCP2 (B9-27) - Body ground | 10 kΩ or higher |
Reconnect the APP sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.INSPECT ECM (VCPA AND VCP2 VOLTAGE) |
![]() |
Disconnect the APP sensor connector.
Turn the ignition switch to the ON position.
Measure the voltage between the terminals of the ECM connector.
| Tester Connections | Specified Conditions |
| VCPA (B9-26) - EPA (B9-20) | 4.5 to 5.0 V |
| VCP2 (B9-27) - EPA2 (B9-21) | 4.5 to 5.0 V |
Reconnect the APP sensor connector.
|
| ||||
| OK | |
| 4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester ON.
Clear DTCs (Click here).
Allow the engine to idle for 15 seconds.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC Output) | Proceed To |
| P2120, P2122, P2123, P2125, P2127, P2128 and P2138 | A |
| No output | B |
|
| ||||
| A | ||
| ||