DTC P1290/22 Engine Coolant Temperature Circuit |
DTC P1292/22 Short in Engine Coolant Temperature Circuit |
DTC P1293/22 Open in Engine Coolant Temperature Circuit |
| DTC No. | Proceed To | DTC Detection Conditions | Trouble Areas |
| P1290/22 | Step 1 | Open or short in Engine Coolant Temperature (Radiator) sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| P1292/22 | Step 4 | Short in Engine Coolant Temperature (Radiator) sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| P1293/22 | Step 2 | Open in Engine Coolant Temperature (Radiator) sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| Temperature Displayed | Malfunctions |
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) or higher | Short circuit |

| 1.READ VALUE OF INTELLIGENT TESTER (RADIATOR COOLANT TEMPERATURE) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp 2.
Read the value displayed on the tester.
| Temperature Displayed | Proceed To |
| -40°C (-40°F) | A |
| 140°C (284°F) or higher | B |
| Between 80°C and 97°C (176°F and 207°F) | C |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE OF INTELLIGENT TESTER (CHECK FOR OPEN HARNESS) |
Confirm good connection of the connector to the ETC (Radiator) sensor.
![]() |
Disconnect the B29 Engine Coolant Temperature (Radiator) sensor connector.
Connect terminals 1 and 2 of the Engine Coolant Temperature (Radiator) sensor connector on the wire harness side.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp 2.
Read the value displayed on the tester.
Reconnect the Engine Coolant Temperature (Radiator) sensor connector.
|
| ||||
| NG | |
| 3.READ VALUE OF INTELLIGENT TESTER (CHECK FOR OPEN IN ECM) |
Confirm good connection of the connectors to the ECM.
![]() |
Disconnect the B29 Engine Coolant Temperature (Radiator) sensor connector.
Connect terminals RTHW and E2 of the ECM connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp 2.
Read the value displayed on the tester.
Reconnect the Engine Coolant Temperature (Radiator) sensor connector.
|
| ||||
| NG | ||
| ||
| 4.READ VALUE OF INTELLIGENT TESTER (CHECK FOR SHORT IN HARNESS) |
![]() |
Disconnect the B29 Engine Coolant Temperature (Radiator) sensor connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp 2.
Read the value displayed on the tester.
Reconnect the Engine Coolant Temperature (Radiator) sensor connector.
|
| ||||
| NG | |
| 5.READ VALUE OF INTELLIGENT TESTER (CHECK FOR SHORT IN ECM) |
![]() |
Disconnect the D1 ECM connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp 2.
Read the value displayed on the tester.
Reconnect the Engine Coolant Temperature (Radiator) sensor connector.
|
| ||||
| NG | ||
| ||