Home › ENGINE · 5L-E › ENGINE CONTROL SYSTEM › ECD SYSTEM

ECD SYSTEM > MIL Circuit

for Preparation Click here


DESCRIPTION

The Malfunction Indicator Lamp (MIL) is used to indicate the ECM's detection of a vehicle malfunction. The instrument panel J/B MET IGN fuse provides circuit power and the ECM provides the circuit ground that illuminates the MIL.
MIL operations should be checked visually:
The MIL should be illuminated when the ignition switch is first turned ON. If the MIL is always on or off, use the intelligent tester and follow the procedures below to determine the cause of the problem.

WIRING DIAGRAM


A106813E01


INSPECTION PROCEDURE

1.CHECK MIL


    FI02547E02
  1. Turn the ignition switch ON.

    Result:
    MIL Condition
    Proceed
    MIL is illuminated
    A
    MIL is not illuminated
    B



B
Go to step 5
A


2.CLEAR DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and push the intelligent tester main switch on.

  1. Read the DTC (Click here).

  1. Clear the DTC (Click here).

  1. Check that MIL is not illuminated.

    OK:
    MIL is not illuminated.



NG
Go to step 3
OK

REPAIR CIRCUIT INDICATED BY OUTPUT DTC 

3.CHECK WIRE HARNESS (FOR SHORT IN WIRE CIRCUIT)


    A062417E01
  1. Disconnect the B10 ECM connector.

  1. Turn the ignition switch ON.

  1. Check that MIL is not illuminated.

    OK:
    MIL is not illuminated.



NG
Go to step 4
OK

REPLACE ECM 

4.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER)


    A062417E01
  1. Disconnect the ECM B10 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for short):
    Tester Connection
    Specified condition
    W (B10-5) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK FOR INTERMITTENT PROBLEMS 

5.INSPECT ECM (CHECK VOLTAGE)


    A062416E18
  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified condition
    W (B10-5) - Body ground
    9 to 14 V



NG
Go to step 6
OK

REPLACE ECM 

6.INSPECT COMBINATION METER (CHECK VOLTAGE)


    A106820E04
  1. Disconnect the combination meter connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified condition
    EGW (H20-32) - Body ground
    9 to 14 V



NG
Go to step 8
OK


7.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER)


    A106812E02
  1. Disconnect the combination meter connector.

  1. Disconnect the ECM B10 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified condition
    EGW (H20-32) - W (B10-5)
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK FOR INTERMITTENT PROBLEMS 

8.INSPECT COMBINATION METER (CHECK VOLTAGE)


    A106820E03
  1. Disconnect the combination meter connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified condition
    IG+ (H20-6) - Body ground
    9 to 14 V



NG
Go to step 9
OK

REPLACE COMBINATION METER 

9.CHECK FUSE (MET IGN FUSE)


    A106793E01
  1. Remove the MET IGN fuse from the instrument panel J/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    MET IGN fuse
    Below 1 Ω (Continuity)



NG
REPLACE FUSE (MET IGN FUSE)
OK


10.CHECK HARNESS AND CONNECTOR (COMBINATION METER - MET IGN FUSE)


    A106821E01
  1. Disconnect the combination meter connectors.

  1. Remove the MET IGN fuse from the instrument panel J/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified condition
    (MET IGN fuse terminal 1 of J/B) - IG+ (H20-6)
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK AND REPLACE HARNESS AND CONNECTOR (MET IGN FUSE - BATTERY)