Home › BODY › SEAT › REAR NO. 1 SEAT ASSEMBLY (for Hold Down Seat Type)

REAR NO. 1 SEAT ASSEMBLY (for Hold Down Seat Type) > REASSEMBLY

for Preparation Click here



1. INSTALL NO.1 SEAT LEG SUB-ASSEMBLY


2. INSTALL NO.1 SEAT LEG SUB-ASSEMBLY


    B101792
  1. Install the No.1 seat leg sub-assembly with the 4 bolts.

    Torque:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }



3. INSTALL WARNING REFLECTOR HOLDER ASSEMBLY


4. INSTALL REAR SEAT CUSHION UNDER COVER


5. INSTALL SEAT TRACK ADJUSTING HANDLE KNOB


6. INSTALL NO.1 SEAT LEG SUB-ASSEMBLY REAR


7. INSTALL REAR SEAT HINGE PIN


8. INSTALL REAR SEAT CUSHION HINGE COVER LOWER


9. INSTALL REAR SEAT LEG STOPPER


10. INSTALL NO.1 SEAT LEG STOPPER HOLDER


11. INSTALL REAR NO.1 SEAT LOCK ASSEMBLY


    B101737
  1. w/o Seat belt:

    1. Install the 2 rear No.1 seat lock assemblies with the 6 bolts.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B105594
  1. w/ Seat belt:

    1. Install the 2 rear No.1 seat lock assemblies with the 4 bolts.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }



12. INSTALL REAR SEAT BELT ASSEMBLY INNER (w/ Seat Belt)

HINT:
Follow the same procedure as for the fixed seat type.



13. INSTALL REAR SEAT BELT ASSEMBLY OUTER (w/ Seat Belt)

HINT:
Follow the same procedure as for the fixed seat type.



14. INSTALL REAR SEATBACK LOCK COVER


15. INSTALL REAR SEAT LOCK HANDLE KNOB


16. INSTALL REAR SEAT LEG SIDE COVER


    B101735
  1. Install the 2 brackets with the 2 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



    B101734
  1. Install the 2 rear seat leg side covers with the 2 screws.



17. INSTALL NO.1 SEATBACK SPRING ASSEMBLY


    B101733
  1. Install the No.1 seatback spring assembly with the 4 bolts.

    Torque:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }



18. INSTALL REAR SEAT RECLINING COVER NO.1 RH


19. INSTALL REAR SEAT RECLINING COVER NO.1 LH


20. INSTALL REAR SEAT CUSHION SHIELD INNER NO.1 RH


21. INSTALL REAR SEAT CUSHION SHIELD INNER NO.1 LH


22. INSTALL NO.1 SEATBACK PAD


23. INSTALL NO.1 SEATBACK COVER SUB-ASSEMBLY
  1. Using hog ring pliers, install the No.1 seatback cover sub-assembly to the No.1 seatback pad with 6 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.

    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


      B113614E01



24. INSTALL NO.1 SEATBACK COVER SUB-ASSEMBLY WITH PAD


25. INSTALL REAR SEAT HEADREST SUPPORT


26. INSTALL REAR SEAT HEADREST SUPPORT


27. INSTALL REAR SEAT HEADREST ASSEMBLY


28. INSTALL NO.1 SEAT CUSHION PAD


29. INSTALL NO.1 SEAT CUSHION COVER SUB-ASSEMBLY
  1. Using hog ring pliers, install the No.1 seat cushion cover sub-assembly to the No.1 seat cushion pad with 14 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.

    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


      B113615E01



30. INSTALL NO.1 SEAT CUSHION COVER SUB-ASSEMBLY WITH PAD


31. INSTALL REAR SEAT RECLINING COVER NO.2 RH


32. INSTALL REAR SEAT RECLINING COVER NO.2 LH


33. INSTALL REAR SEAT HINGE PIN


34. INSTALL REAR SEATBACK COVER RH


35. INSTALL REAR SEATBACK COVER LH


36. INSTALL RECLINING ADJUSTER COVER RH


37. INSTALL RECLINING ADJUSTER COVER LH


38. INSTALL RECLINING ADJUSTER RELEASE HANDLE NO.1 RH


39. INSTALL RECLINING ADJUSTER RELEASE HANDLE NO.1 LH


40. INSTALL RECLINING RELEASE HANDLE SUB-ASSEMBLY