POWER STEERING GEAR > REASSEMBLY |
| 1. INSTALL POWER STEERING CYLINDER TUBE OIL SEAL |
Install the spacer to the power steering rack housing.
Apply power steering fluid to the lip of a new power steering cylinder tube oil seal.
![]() |
Install the power steering cylinder tube oil seal to the rack housing at a slant.
Using SST, insert the power steering cylinder tube oil seal by pushing the SST in by hand until the oil seal passes the 2 ports.
Install SST (09631-00200) to SST (09951-07360) upside down.
![]() |
Using SST, level the power steering cylinder tube oil seal by pushing the SST in by hand.
![]() |
Using SST and a press, install the power steering cylinder tube oil seal.
| 2. INSTALL POWER STEERING RACK |
Coat a new O-ring with power steering fluid and install it to the power steering rack.
![]() |
Expand a new oil seal with your fingers.
Coat the oil seal with power steering fluid.
![]() |
Install the oil seal to the steering rack, and adjust with your fingers.
![]() |
Apply molybdenum disulfide lithium base grease to the rack teeth ends.
Affix SST to the steering rack.
Coat SST with power steering fluid.
Install the steering rack to the rack housing.
Remove the SST.
| 3. INSTALL CYLINDER END STOPPER |
Body type narrow:
![]() |
Wrap protective tape around the RH side of the power steering rack and apply power steering fluid.
Apply power steering fluid to the lip of a new cylinder end stopper oil seal.
Install the cylinder end stopper oil seal to the RH side of the rack housing.
Remove the protective tape from the power steering rack.
Apply power steering fluid to a new cylinder end stopper O-ring.
Install the cylinder end stopper O-ring to the cylinder end stopper.
![]() |
Install a new cylinder end stopper bushing to the cylinder end stopper.
Apply molybdenum disulfide lithium base grease to the entire inner side of the cylinder end stopper.
Install the tube support retainer.
![]() |
Using SST, install the cylinder end stopper to the rack housing.
![]() |
Tighten the bolt.
Body type wide:
![]() |
Wrap protective tape around the RH side of the power steering rack and apply power steering fluid.
Apply power steering fluid to the lip of a new cylinder end stopper oil seal.
Install the cylinder end stopper oil seal to the RH side of the rack housing.
Remove the protective tape from the power steering rack.
Install the spacer to the rack housing.
Apply power steering fluid to a new cylinder end stopper O-ring.
Install the cylinder end stopper O-ring to the cylinder end stopper.
Install a new cylinder end stopper bushing to the cylinder end stopper.
![]() |
Apply molybdenum disulfide lithium base grease to the entire inner side of the cylinder end stopper.
![]() |
Using SST, install the cylinder end stopper to the rack housing.
| 4. AIR TIGHTNESS TEST |
![]() |
Install SST and a vacuum pump to the rack housing.
Apply a vacuum of 53 kPa (398 mmHg, 15.65 in.Hg) for approximately 30 seconds.
Check that there is no change in the vacuum pressure.
If there is a change in the vacuum pressure, check the installation of the oil seals.
| 5. INSTALL POWER STEERING CONTROL VALVE UPPER OIL SEAL |
Coat the power steering control valve upper bearing and a new power steering control valve upper oil seal lip with power steering fluid.
![]() |
Using SST and a press, install the power steering control valve upper oil seal.
![]() |
Using SST and a press, install the control valve upper bearing.
| 6. INSTALL POWER STEERING CONTROL VALVE LOWER OIL SEAL |
Coat a new power steering control valve lower oil seal lip with power steering fluid.
![]() |
Using SST and a press, install the power steering control valve lower oil seal.
| 7. INSTALL POWER STEERING CONTROL VALVE |
![]() |
Expand 4 new control valve spacers with your fingers.
Coat the 4 valve spacers with power steering fluid.
![]() |
Install the 4 valve spacers to the control valve, and adjust with your fingers.
Wrap the serration of the power steering control valve with protective tape.
Coat the control valve with power steering fluid.
Install the control valve into the control valve housing.
![]() |
Install the control valve housing with the control valve and a new gasket to the rack housing with the 2 bolts.
![]() |
Install the dust boot.
| 8. INSTALL STEERING RACK GUIDE |
Install the rack guide seat to the power steering rack guide.
Apply molybdenum disulfide lithium base grease to the compression spring and the contact surface of the rack guide seat and the power steering rack.
Install the compression spring and the rack guide.
Apply sealant to 2 or 3 threads of the rack guide spring cap.
Using a straight hexagon wrench 24 mm (0.94 in.), install the rack guide spring cap.
| 9. INSPECT TOTAL PRELOAD |
Using a straight hexagon wrench 24 mm (0.94 in.), tighten the power steering rack guide spring cap.
Using a straight hexagon wrench 24 mm (0.94 in.), loosen the power steering rack guide spring cap.
Temporarily install the steering rack ends to prevent steering rack over stroke.
![]() |
Using SST, fully turn the power steering rack right and left 10 times to settle.
![]() |
Using a straight hexagon wrench 24 mm (0.94 in.), tighten the power steering rack guide spring cap in small amounts until the preload is within the specified range.
![]() |
Using SST, install the power steering rack guide spring cap nut.
![]() |
Using SST, inspect the total preload.
| 10. INSTALL RACK END SUB-ASSEMBLY |
Install 2 new claw washers.
![]() |
Using SST, install the steering rack end sub-assembly (RH side).
![]() |
Using SST, install the steering rack end sub-assembly (LH side).
![]() |
Using a brass bar and a hammer, stake the 2 claw washers.
| 11. INSTALL STEERING RACK BOOT NO.2 |
![]() |
Apply silicon grease to the inside of the small opening of the steering rack boot No.2.
![]() |
Temporarily install a new steering rack boot No.2 clamp to the large opening of the steering rack boot No.2 at the position shown by arrow (A).
Install the rack boot No.2 to the groove on the rack housing.
| 12. INSTALL STEERING RACK BOOT NO.1 |
| 13. INSTALL STEERING RACK BOOT NO.2 CLAMP |
![]() |
Using pliers and a screwdriver, install the steering rack boot No.2 clamp.
| 14. INSTALL STEERING RACK BOOT NO.1 CLAMP |
| 15. INSTALL STEERING RACK BOOT CLIP |
Using pliers, install the 2 boot clips.
![]() |
Using SST, turn the pinion and check that the rack boots expand and contract smoothly.
| 16. INSTALL TIE ROD END SUB-ASSEMBLY LH |
![]() |
Install the lock nut and the tie rod sub-assembly LH to the rack end sub-assembly until the matchmarks are aligned.
| 17. INSTALL TIE ROD END SUB-ASSEMBLY RH |
| 18. INSTALL STEERING RIGHT TURN PRESSURE TUBE |
![]() |
Using SST, install the steering right turn pressure tube.
| 19. INSTALL STEERING LEFT TURN PRESSURE TUBE |
![]() |
Using SST, install the steering left turn pressure tube.