PROPELLER SHAFT ASSEMBLY (for Super Long Wheelbase) > REASSEMBLY |
| 1. INSTALL UNIVERSAL JOINT SPIDER ASSEMBLY |
![]() |
Apply MP grease No.2 to a new spider and bearings.
Fit the spider into the flange yoke.
![]() |
Using SST, install the bearings on the spider.
Using SST, adjust both bearings so that the snap ring grooves are at the maximum and equal in width.
Install 2 new snap rings with the same thickness which allow 0.05 mm (0.002 in.) or less axial play.
| Parts No. | Thickness mm (in.) | Mark |
| 90520-25039 | 2.28 to 2.30 (0.0898 to 0.0906) | 1 |
| 90520-25040 | 2.30 to 2.32 (0.0906 to 0.0913) | 2 |
| 90520-25041 | 2.32 to 2.34 (0.0913 to 0.0921) | - |
| 90520-25042 | 2.34 to 2.36 (0.0921 to 0.0929) | Brown |
| 90520-25043 | 2.36 to 2.38 (0.0929 to 0.0937) | Blue |
| 90520-25044 | 2.38 to 2.40 (0.0937 to 0.0945) | 6 |
| 90520-25045 | 2.40 to 2.42 (0.0945 to 0.0953) | 7 |
| 90520-25046 | 2.42 to 2.44 (0.0953 to 0.0961) | 8 |
| 90520-25047 | 2.44 to 2.46 (0.0961 to 0.0969) | ![]() |
| 90520-25048 | 2.46 to 2.48 (0.0969 to 0.0976) | 10 |
| 90520-25049 | 2.48 to 2.50 (0.0976 to 0.0984) | A |
| 90520-25050 | 2.50 to 2.52 (0.0984 to 0.0992) | B |
| 90520-25051 | 2.52 to 2.54 (0.0992 to 0.1) | C |
| 90520-25052 | 2.54 to 2.56 (0.1 to 0.1008) | D |
| 90520-25053 | 2.56 to 2.58 (0.1008 to 0.1016) | E |
| 90520-25054 | 2.18 to 2.20 (0.0858 to 0.0866) | J |
| 90520-25055 | 2.20 to 2.22 (0.0866 to 0.0874) | K |
| 90520-25056 | 2.22 to 2.24 (0.0874 to 0.0882) | F |
| 90520-25057 | 2.24 to 2.26 (0.0882 to 0.089) | G |
| 90520-25058 | 2.26 to 2.28 (0.089 to 0.0898) | H |
![]() |
Using a hammer, tap the flange yoke until there is no clearance between the spider bearing outer race and snap ring.
Align the matchmarks on the propeller shaft assembly and flange yoke.
![]() |
Using SST, adjust both bearings so that the snap ring grooves are at the maximum and equal in width.
Install 2 new snap rings with the same thickness which allow 0.05 mm (0.002 in.) or less axial play.
| Parts No. | Thickness mm (in.) | Mark |
| 90520-25039 | 2.28 to 2.30 (0.0898 to 0.0906) | 1 |
| 90520-25040 | 2.30 to 2.32 (0.0906 to 0.0913) | 2 |
| 90520-25041 | 2.32 to 2.34 (0.0913 to 0.0921) | - |
| 90520-25042 | 2.34 to 2.36 (0.0921 to 0.0929) | Brown |
| 90520-25043 | 2.36 to 2.38 (0.0929 to 0.0937) | Blue |
| 90520-25044 | 2.38 to 2.40 (0.0937 to 0.0945) | 6 |
| 90520-25045 | 2.40 to 2.42 (0.0945 to 0.0953) | 7 |
| 90520-25046 | 2.42 to 2.44 (0.0953 to 0.0961) | 8 |
| 90520-25047 | 2.44 to 2.46 (0.0961 to 0.0969) | ![]() |
| 90520-25048 | 2.46 to 2.48 (0.0969 to 0.0976) | 10 |
| 90520-25049 | 2.48 to 2.50 (0.0976 to 0.0984) | A |
| 90520-25050 | 2.50 to 2.52 (0.0984 to 0.0992) | B |
| 90520-25051 | 2.52 to 2.54 (0.0992 to 0.1) | C |
| 90520-25052 | 2.54 to 2.56 (0.1 to 0.1008) | D |
| 90520-25053 | 2.56 to 2.58 (0.1008 to 0.1016) | E |
| 90520-25054 | 2.18 to 2.20 (0.0858 to 0.0866) | J |
| 90520-25055 | 2.20 to 2.22 (0.0866 to 0.0874) | K |
| 90520-25056 | 2.22 to 2.24 (0.0874 to 0.0882) | F |
| 90520-25057 | 2.24 to 2.26 (0.0882 to 0.089) | G |
| 90520-25058 | 2.26 to 2.28 (0.089 to 0.0898) | H |
![]() |
Using a hammer, tap the flange yoke until there is no clearance between the spider bearing outer race and snap ring.
| 2. INSPECT UNIVERSAL JOINT SPIDER ASSEMBLY |
![]() |
Check that the spider bearing rotates smoothly.
Check that there is no play in the spider bearing.
![]() |
Using a spring tension gauge, hang the hook of the spring tension gauge on the bolt hole of the flange yoke and measure the rotating force.
| 3. INSTALL CENTER SUPPORT BEARING ASSEMBLY NO.1 |
![]() |
Set the center support bearing assembly No.1 on the intermediate shaft assembly, as shown in the illustration.
![]() |
Align the matchmarks on the universal joint flange and intermediate shaft assembly, and place the universal joint flange on the intermediate shaft assembly.
Hold the intermediate shaft assembly in a vise between aluminium plates.
Install the washer.
![]() |
Using SST to hold the universal joint flange, press the center support bearing assembly No.1 into position by tightening a new nut.
Loosen the nut.
Retighten the nut.
![]() |
Using a chisel and a hammer, stake the nut.
| 4. INSTALL PROPELLER SHAFT ASSEMBLY |
![]() |
Align the matchmarks on the intermediate shaft flange and the propeller shaft flange, and install the shaft with the 4 bolts, washers and nuts.