Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



POWER WINDOW MASTER SWITCH

B112700E01

  1. Disconnect the K5 (L5) switch with the K5 (L5) switch connector still connected.

  2. Measure the voltage according to the value(s) in the table below.

    Standard:

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3 (VCC) - 2(GND)
    W - BR
    Power supply
    Ignition switch OFF → ON
    Below 1 V → 10 to 14 V
    4 (U) - 1 (E)
    Y - W-B
    Power window motor UP output
    Ignition switch ON, power window switch OFF → UP (Manual/Auto)
    Below 1 V → 10 to 14 V
    B (6) - E (1)
    L - W-B
    +B (B) power supply
    Ignition switch ON
    10 to 14 V
    BW (7) - E (1)
    R - W-B
    +B (BW) power supply
    Constant
    10 to 14 V
    9 (D) - 1 (E)
    G - W-B
    Power window motor DOWN output
    Ignition switch ON, power window switch OFF → DOWN (Manual/Auto)
    Below 1 V → 10 to 14 V
    CTY (11) - E (1)
    R - W-B
    Door courtesy switch signal
    Driver side door OPEN → CLOSE
    10 to 14 V → Below 1 V
    13 (UH) - 1 (E)
    L - W-B
    Power window motor UP output (Remote)
    Ignition switch ON, power window switch OFF → UP (Remote)
    Below 1 V → 10 to 14 V
    14 (PLS) - 2(GND)
    L - BR
    Power window motor sensor signal
    Power window operating
    Pulse generation
    15 (DH) - 1 (E)
    R-L - W-B
    Power window motor DOWN output (Remote)
    Ignition switch ON, power window switch OFF → DOWN (Remote)
    Below 1 V → 10 to 14 V
    17 (PLS2) - 2(GND)
    Y - BR
    Power window motor sensor signal
    Power window operating
    Pulse generation

  3. Disconnect the K5 (L5) switch connector.

  4. Measure the voltage and resistance according to the value(s) in the table below.

    Standard resistance:

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E (1) - Body ground
    W-B - Body ground
    Ground
    Constant
    Below 1 Ω

    If the result is not as specified, there may be a malfunction on the wire harness side.


POWER WINDOW SWITCH

B111212E01

  1. Disconnect the L6 (K6) switch with the L6 (K6) switch connector still connected.

  2. Measure the voltage according to the value(s) in the table below.

    Standard voltage:

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    1 (D) - Body ground
    G - Body ground
    Power window motor DOWN output
    Ignition switch ON, power window switch OFF → DOWN
    Below 1 V → 10 to 14 V
    2 (SD) - Body ground
    R-L - Body ground
    Power window motor DOWN output (Remote)
    Ignition switch ON, power window master switch OFF → DOWN (Remote)
    Below 1 V → 10 to 14 V
    3 (U) - Body ground
    Y - Body ground
    Power window motor UP output
    Ignition switch ON, power window switch OFF → UP
    Below 1 V → 10 to 14 V
    B (4) - Body ground
    L - Body ground
    +B (B) power supply
    Ignition switch ON
    10 to 14 V
    5 (SU) - Body ground
    L - Body ground
    Power window motor UP output (Remote)
    Ignition switch ON, power window master switch OFF → UP (Remote)
    Below 1 V → 10 to 14 V


INSTRUMENT PANEL J/B

B111255E01


Standard voltage:

Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
B (5B-36) - Body ground
W-L - Body ground
+B (B) power supply
Ignition switch ON
10 to 14 V
BW (5H-1) - Body ground
W-R - Body ground
+B (BW) power supply
Always
10 to 14 V